-
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 -
Arduino UNO SMD Atmega328P Development Board
Features-
- Flash Memory – 32 KB (ATmega32u4) of which 4 KB used by boot loader
- SRAM – 2 KB (ATmega328P)
- EEPROM – 1 KB (ATmega328P)
₹290.00₹550.00Arduino UNO SMD Atmega328P Development Board
₹290.00₹550.00 -
Uno Rev3 SMD Atmega328P Compatible with Arduino
Features-
- Flash Memory – 32 KB (ATmega32u4) of which 4 KB used by boot loader
- SRAM – 2 KB (ATmega328P)
- EEPROM – 1 KB (ATmega328P)
₹290.00₹550.00Uno Rev3 SMD Atmega328P Compatible with Arduino
₹290.00₹550.00 -
Multifunction Shield For Arduino Uno / Leonardo
Features:
- 4 digit 7-segment LED display module driven by two serial 74HC595’s.
- 4 x surface mount LED’s in a parallel configuration.
- 10K adjustable precision potentiometer.
- 3 x Independent push buttons.
- Piezo buzzer.
- DS18B20 temperature sensor interface.
- LM35 temperature sensor interface.
- Infrared receiver interface.
- Serial interface header for convenient connection to serial modules such as Bluetooth, a wireless interface, voice module, a voice recognition module, etc.
₹241.00 -
Nano V3 with USB Cable Compatible with Arduino
- Operating Voltage (logic level): 5V
- With USB cable and Soldered Connector
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
₹240.00₹500.00Nano V3 with USB Cable Compatible with Arduino
₹240.00₹500.00 -
L293D Motor Driver Shield Expansion Board
- Drive 4 DC motors with speed and direction control
- Drive 2 stepper motors
- Drive 2 servo motors
- 4.5 – 25V motor voltage range
- 1.2A peak current per channel (600mA continuous)
₹125.00 -
Expansion Testing Interface Board for Microcontrollers
Features:
Input Output Board for Arduino 8051 AVR Raspberry Pi
8 LEDs and 4 Switches
5V Relay, Buzzer for Output test
TSOP, LDR and LM35D Temperature Sensor for Input Testing
Potentiometer for Varying Sensitivity.₹115.00 -
Proto Shield Prototype expansion board for Arduino UNO
Features:
Power rails down the middle and sides
A reset button and an extra general use button
2x 3mm general use LEDs, red and green, as well as 2 matching resistors
A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
A surface-mount chip area for up to 14 SOIC size parts
Compatible with tiny breadboards
Every pin is brought out
Gold plated pads₹82.00₹90.00 -
Transparent Acrylic Case Shell Enclosure Gloss Box For Arduino UNO R3
- UNO Case is to enclose Development Board only.
- With screw copper pillar and installation instructions.
- To protect your little computer against damages, dust and scratches Clear Top and Bottom.
- This case provides easy access to all ports.
- It requires no tools for easy assembly and disassembly.
- Simply Clicks Together Enclosure.
₹55.00 -
White Type C cable – 1m for Arduino Nano V3.0
Features:
- Allows you to connect Arduino NanoV3.0 with USB port to the computer.
- Good data transfer rate.
₹37.62 -
Micro USB 2.0 Cable Type A/B for Arduino Nano
- Up to 480 Mbps data transfer rate.
- USB Type: Type-A to Mini-B
- Weight: 15 gm
- Length: 30 cm
- Exclusively designed for Arduino boards.
₹18.00 -
USB 2.0 Cable Type A/B for Arduino UNO
- Fully compatible with the PC.
- Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
- Aluminum under mold shield helps meet FCC requirements on KMI/RFI interference.
- Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
₹18.00
