-
Original Arduino Uno Rev3 SMD Atmega328P Development Board
Features-
- Flash Memory – 32 KB (ATmega32u4) of which 4 KB used by boot loader
- SRAM – 2 KB (ATmega328P)
- EEPROM – 1 KB (ATmega328P)
₹1,635.00₹1,999.00(excl. GST)Original Arduino Uno Rev3 SMD Atmega328P Development Board
₹1,635.00₹1,999.00(excl. GST) -
Transparent Acrylic Case Shell Enclosure Gloss Box For Arduino UNO R3
- UNO Case is to enclose Development Board only.
- With screw copper pillar and installation instructions.
- To protect your little computer against damages, dust and scratches Clear Top and Bottom.
- This case provides easy access to all ports.
- It requires no tools for easy assembly and disassembly.
- Simply Clicks Together Enclosure.
₹55.00 (excl. GST)Transparent Acrylic Case Shell Enclosure Gloss Box For Arduino UNO R3
₹55.00 (excl. GST) -
Pro Mini Atmega328 5V and 16MHz
- Microcontroller: ATmega328
- Circuit Operating Voltage: 5V
- Clock frequency: 16MHz.
- Digital I/O Pins: 14
- 8 analog input port: A0 ~ A7.
- A pair of TTL level serial port transceiver : RX / TX.
- 6 PWM port: D3, D5, D6, D9, D10, D11.
- Support serial download.
₹650.00 (excl. GST)Pro Mini Atmega328 5V and 16MHz
₹650.00 (excl. GST) -
Nano V3 with USB Cable Compatible with Arduino
- Operating Voltage (logic level): 5V
- With USB cable and Soldered Connector
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
₹160.00₹500.00(excl. GST)Nano V3 with USB Cable Compatible with Arduino
₹160.00₹500.00(excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
₹850.00 (excl. GST)
W5100 Network Expansion Board Ethernet Shield
₹850.00 (excl. GST) -
Micro USB 2.0 Cable Type A/B for Arduino Nano
- Up to 480 Mbps data transfer rate.
- USB Type: Type-A to Mini-B
- Weight: 15 gm
- Length: 30 cm
- Exclusively designed for Arduino boards.
₹18.00 (excl. GST)Micro USB 2.0 Cable Type A/B for Arduino Nano
₹18.00 (excl. GST) -
USB 2.0 Cable Type A/B for Arduino UNO
- Fully compatible with the PC.
- Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
- Aluminum under mold shield helps meet FCC requirements on KMI/RFI interference.
- Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
₹18.00 (excl. GST)USB 2.0 Cable Type A/B for Arduino UNO
₹18.00 (excl. GST) -
Proto Shield Prototype expansion board for Arduino UNO
Features:
Power rails down the middle and sides
A reset button and an extra general use button
2x 3mm general use LEDs, red and green, as well as 2 matching resistors
A pass-thru ICSP stacking header so you can stack any kind of shield on top, and/or use an AVR programmer
A surface-mount chip area for up to 14 SOIC size parts
Compatible with tiny breadboards
Every pin is brought out
Gold plated pads₹82.00₹90.00(excl. GST)Proto Shield Prototype expansion board for Arduino UNO
₹82.00₹90.00(excl. GST) -
L293D Motor Driver Shield Expansion Board
- Drive 4 DC motors with speed and direction control
- Drive 2 stepper motors
- Drive 2 servo motors
- 4.5 – 25V motor voltage range
- 1.2A peak current per channel (600mA continuous)
₹125.00 (excl. GST)L293D Motor Driver Shield Expansion Board
₹125.00 (excl. GST) -
Expansion Testing Interface Board for Microcontrollers
Features:
Input Output Board for Arduino 8051 AVR Raspberry Pi
8 LEDs and 4 Switches
5V Relay, Buzzer for Output test
TSOP, LDR and LM35D Temperature Sensor for Input Testing
Potentiometer for Varying Sensitivity.₹115.00 (excl. GST)Expansion Testing Interface Board for Microcontrollers
₹115.00 (excl. GST) -
Arduino Mega 2560 R3 with USB Cable Compatible with Arduino
- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 256 KB of which 8 KB used by bootloader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
- USB Host Chip: MAX3421E
- Length:101.98mm/4.01in
- Width:53.63mm/2.11in
- Height:15.29mm/0.60in
₹850.00₹1,475.00(excl. GST)Arduino Mega 2560 R3 with USB Cable Compatible with Arduino
₹850.00₹1,475.00(excl. GST)
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Mechanical Hardware Tools and Accessories
- Power Supply and Prototypes
- Robotics and Hobbies
- Sensors
- Scientific Tools and Equipments
- Other Tools and Equipment’s
- Bulk/Wholesale
