-
A4988 Stepper Motor Driver Controller Board- RED
Controller Board
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor: Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
₹49.00 -
Waveshare 12-bit I2C 16-Channel Servo Driver for micro: bit
Features of I2C 16-Channel Servo Driver:
- micro: bit edge connector, directly pluggable
- I2C controlled, using only 2 pins
- Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales)
- Integrates 5V regulator, up to 3A output current, can be powered from the battery through VIN terminal
- Standard servo interface supports commonly used servo such as SG90, MG90S, MG996R, etc.
- Reserved I2C control pins, allows working with other control boards
- Comes with development resources and manual (micro: bit graphical examples like Bluetooth/2.4G wireless remote control)
₹1,257.00 -
MP3-TF-16P MP3 SD Card Module with Serial Port
Application
- Car navigation voice broadcast
- Road transport inspectors, toll voice prompts
- The train station, bus station voice prompts security check
- Electric power, telecommunications, financial operating room voice prompts
- The vehicle into or out of the channel to verify the voice prompts
- Border control channel voice prompts
- Multi-channel voice alarm or voice guidance equipment operation
- Electric sightseeing bus safety with voice notices
- Electrical and mechanical equipment failure alarm
- Fire alarm voice prompts
- Automatic broadcasting equipment, regular broadcast.
Specifications and Features :
- Supports sampling rates (kHz): 8 / 11.025 / 12/16 / 22.05 / 24/32 / 44.1 / 48.
- 24-bit DAC output, dynamic range support: 90dB, SNR support: 85dB.
- Fully supports FAT16, FAT32 file system, maximum support 32G TF card, support U disk to 32G, 64M bytes of NOR FLASH.
- A variety of control modes are available. IO control mode, serial mode, AD key control mode.
- The broadcast language spots feature, you can pause the background music being played. Advertising finished playing back background sound to continue playing.
- The audio data is sorted by folder, supports up to 100 folders, folders can assign every 255 Tracks
7,30 level adjustable volume, adjustable EQ 6.
₹82.00 -
5V 8 Channel Relay Module
Features:
- The 8550 transistor drive, drive ability.
- A fixed bolt holes for easy installation.
- It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red)
- Relay control interface by single-chip IO.
- Low-level suction close, high-level release.
- Easy to use, simple 3 line structure.
₹285.005V 8 Channel Relay Module
₹285.00 -
LED Traffic Lights Signal Module / Digital Signal Output Traffic Light Module
- PCB Size: 60 x 20 x 13.5 (LxWxH)mm.
- Color: red, yellow, green
- LED Size: 10mm x 7.
- Brightness: Normal brightness.
- Voltage: 5V.
- Interface: common cathode red yellow green control.
₹38.00 -
5V 16 Channel Relay Module with Light Coupling LM2596S Power Supply
Features :
- 5V 16-Channel Relay Module with AC contact capacity of 10A 250V and optocoupler protection.
- Onboard power supply module does not need an external power supply. I / O port driver is active low.
- The module can be used as a microcontroller development board module and also as appliance control, PLC extended output.
- It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
- The 1-16 road can be any full on/off or any road.
- Each relay common terminal “COM” are independent, user-friendly access to different signals, each relay are normally closed and normally open with the port.
- Each relay is equipped with motion lights.
- All interfaces can be directly connected through the terminal leads, very convenient.
₹546.00 -
4×3 Matrix Membrane Type Keypad -12 Keys
Specifications of 4×3 Matrix Keypad -12 Keys:-
- Length of cable + connector: 93mm
- 7-pin 0.1″ pitch connector
- Weight: 7.5 grams
- Keypad dimensions: 68.5mm x 76.5mm x 1mm
4×3 Matrix Membrane Keypad Features:-
- Ultra-thin design & adhesive backing provides easy integration to any project
- Excellent price-performance ratio
- Easy communication with any microcontroller
- Sticker can peel off for adhesive mounting.
- Used widely in industrial and home electronic equipments, instrument, etc.
- This allows a microcontroller to ‘scan’ the 7 output pins to see which of the 12 buttons is being pressed
₹40.00 -
0.96 Inch I2C/IIC 4pin OLED Display Module BLUE
Features of 4 pin 128 x 64 OLED Display
- Super High Brightness (Adjustable)
- Super High Contrast (Adjustable)
- Embedded Driver/Controller
- Display size: 0.96″
- Resolution radio:128 x 64
- Interface modes: I2C/IIC
- working voltage: 3.3V
- Control Chip: SSD1306
₹165.00 -
BTS7960 Stepper Motor Driver Module 43A H-Bridge High-Power
Features :
- PWM capability of up to 25 kHz combined with active freewheeling.
- Switched mode current limitation for reduced power dissipation in overcurrent.
- Status flag diagnosis with current sense capability.
- Overtemperature shut down with latch behavior.
- Overvoltage lockout.
- Undervoltage shut down.
- Driver circuit with logic level inputs.
- Adjustable slew rates for optimized EMI.
- 74AHC244 Schmitt-trigger Octal buffer/line driver for ESD protection (Inputs accepts voltages higher than VCC).
Input port:
- RPWM: forward level or PWM signal input, active high.
- LPWM: Reverse level or PWM signal input, active high.
- R_EN: forward drive enable input, high-level enable, low level off.
- L_EN: Reverse drive enable input, high-level enable, low level off.
- R_IS: forward drive current alarm output.
- L_IS: Reverse drive current alarm output.
- VCC: +5 V power output, 5V power supply connection with the microcontroller.
- GND: signal common low end.
₹324.00 -
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
Features :
- Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Adjustable current control lets you set the maximum current output with a potentiometer. Hence lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- 45 V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
- Can interface directly with 3.3 V and 5 V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- 4-layer, 2 oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
₹126.00 -
Cytron 20Amp 6V-30V DC Motor Driver (2 Channels)
Features:
- Bidirectional control for two brushed DC motors.
- Operating Voltage: DC 6V to 30V.
- Maximum Motor Current (Each Channel): 20A continuous, 60A peak.
- Buttons for quick testing.
- LEDs for motors output state.
- Temperature protection.
- Undervoltage shutdown.
Example Application: Automated Guided Vehicle (AGV), Solar Tracker, Game Simulator, Mobile Robot, Automation Machine.
₹2,660.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
