-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 -
L293D Motor Driver Board
- The driver two holes of 3 mm dia.
- Male burg-stick connectors for supply, ground and input connection.
- Screw terminal connectors for easy motor connection.
- High noise immunity inputs.
₹45.00L293D Motor Driver Board
₹45.00 -
A4988 Stepper Motor Driver Controller Board- RED
Controller Board
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor: Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
₹49.00 -
DC PWM Motor Speed Controller
- The maximum output power:30W
- Input supply voltage:1.8V-15VDC
- The Maximum continuous output current:2A
- Duty Cycle adjustable:0%-100%
₹65.00 -
A4988 driver Stepper Motor Driver
Features :
- Automatic current decay mode detection/choice.
- Mixed with slow current decay mode.
- The low power dissipation of synchronous rectifier.
- Internal UVLO(ultra voltage lockout).
- Crossover current protection.
- Thermal shutdown circuit.
- Ground fault protection.
- Loading and short circuit protection.
- The optional five-step mode: full, 1/2, 1/4, 1/8 and 1/16.
₹78.00 -
28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver
- Rated voltage: 5V DC
- Reduction Ratio: 64:1
- Step Angle: 5.625° /64
- Frequency: 100Hz
- Self-positioning Torque: >34.3mN.m
- Friction torque: 600-1200 gf.cm
- Pull in torque: 300 gf.cm
₹95.00₹125.0028BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver
₹95.00₹125.00 -
L298N 2A Current Motor Driver Board
- Lo Logical voltage:Â 5V
- Drive voltage: 5V-35V
- Logical current:Â 0-36mA
- Drive current: 2A (max. single bridge)
- Max power:Â 25W
- Dimensions:Â 44 x 44 x 28 (LxWxH)mm
- Weight:Â 26 gm
₹99.00 -
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
Features :
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
₹116.00 -
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
Features :
- Microstep resolutions:Â full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Adjustable current control lets you set the maximum current output with a potentiometer. Hence lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- 45Â V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
- Can interface directly with 3.3Â V and 5Â V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- 4-layer, 2Â oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
₹126.00 -
Motor Driver Module TA6586 Based
Features:
- Heavy-duty screw terminal for the input.
- Can be connected directly to the 433MHz receiver output.
- Can drive up to 5A of current.
- Drives 2 motors.
₹165.00Motor Driver Module TA6586 Based
₹165.00 -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
