No products in the cart.
2 Channel 5V Relay Module
- The module using Songle relay control.
- AC voltage 250V, AC current 10A, maximum DC voltage 30V DC current maximum 10A.
- Power indicator (green), Two ways of relay status indicator light (red).
- Using 8550 transistor-driven, strong driving ability.
- Has the fixed bolt hole and easy installation.
₹55.00 (Price is Exclusive of GST)2 Channel 5V Relay Module
₹55.00 (Price is Exclusive of GST)1 Channel 5V Relay Module
- There is a normally open and one normally closed contact.
- The control DC or AC signal, you can control 220V AC load.
- Blue KF301 terminals to the control line is more convenient.
- With the power supply and relay instructions, pull off, disconnect does not shine.
- The module complies with international safety standards, the control area and the load region isolation trench.
₹35.00 (Price is Exclusive of GST)1 Channel 5V Relay Module
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)1 Channel 5V Relay Module with Optocoupler
1 channel relay board
– Operating Voltage 5V
– Max Current : 20mA
– Relay Contact Current Capacity at AC250V: 10A₹35.00 (Price is Exclusive of GST)1 Channel 5V Relay Module with Optocoupler
₹35.00 (Price is Exclusive of GST)Laser sensor Module 650nm 6mm 5V 5mW Red Laser
- Voltage: 3.0 V – 5 V.
- Driver: APC circuit.
- Line length: about 135 mm.
- Transmit power: 58mW.
- Operating Current: 40mA.
- Operating Current: 40mA.
- Operating temperature: -36◦C ~ 65◦C.
₹39.00 (Price is Exclusive of GST)Laser sensor Module 650nm 6mm 5V 5mW Red Laser
₹39.00 (Price is Exclusive of GST)1 Channel 12V Relay Module
- The relay high-level pull-in, the module contains current-limiting resistance, a high level can be DC +, microcontroller I / O port can be set high;
- Fault-tolerant design, even if the control line is broken, the relay will not move;
- Power indicator (red), 1 relay status indicator (blue)
- User-friendly interface design, all interfaces can be directly connected through the terminal leads, very convenient
- With four fixing bolt holes, easy to install
₹45.00 (Price is Exclusive of GST)1 Channel 12V Relay Module
₹45.00 (Price is Exclusive of GST)Buzzer Module Board-3.3 to 5V
- Operating voltage: 3.3V-5V
- PCB Dimension: 3.1cm*1.3cm.
- Color: Blue
- Easy to use
₹30.00 (Price is Exclusive of GST)Buzzer Module Board-3.3 to 5V
₹30.00 (Price is Exclusive of GST)Dual-axis XY Joystick Module
- Input voltage range: DC 3.3V to 5V, Quality rocker, long life, stable performance
- Two analog outputs, one digital output
- X, y-axis output of the two potentiometers can be read out through the a to d converter
- Cross joystick is a bi-directional 10K resistor, with the rocker in different directions, the tap resistance with the change. This module uses 5V power supply, the original state of X, Y read voltage of 2.5V or so, when pressed with the arrow direction, the read voltage value increases with the maximum to 5V; arrows in the opposite direction to press, read the voltage decreases , The minimum is 0V.
- Package content: 1 joystick module
₹28.00 (Price is Exclusive of GST)Dual-axis XY Joystick Module
₹28.00 (Price is Exclusive of GST)2 Channel 12V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 (Price is Exclusive of GST)2 Channel 12V Relay Module with Optocoupler
₹65.00 (Price is Exclusive of GST)4 Channel 12V Relay Module with Optocoupler
- Operating Voltage: 12V DC
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- Freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
- LED Status indicators to indicate the relay ON/OFF status
- Mounting holes provided
₹150.00 (Price is Exclusive of GST)4 Channel 12V Relay Module with Optocoupler
₹150.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)2 Channel 5V Relay Module
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 (Price is Exclusive of GST)2 Channel 5V Relay Module
₹65.00 (Price is Exclusive of GST)
