-
Dual Channel Digital Power Board XH-M543, DC12-26V 2x120W DIY Module High Power Stereo Amp Board for Car Vehicle Computer Speaker DIY Home Theater Audio System
- Strong TPA3116D2 chip is a digital power amplifier chip, with low idle loss characteristics,makes it work well and quickly.
- On board front-facing IC to improve the input sensitivity, high-definition sound quality
- This product has the characteristics of loud sound ,the capacitance are large, ,excellent sound quality.
- There is no solder joint on the back of the circuit board,the chip capacitors and the solder solder board together, so there is no possibility of short circuit.
₹665.00 -
5V 16 Channel Relay Module with Light Coupling LM2596S Power Supply
Features :
- 5V 16-Channel Relay Module with AC contact capacity of 10A 250V and optocoupler protection.
- Onboard power supply module does not need an external power supply. I / O port driver is active low.
- The module can be used as a microcontroller development board module and also as appliance control, PLC extended output.
- It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
- The 1-16 road can be any full on/off or any road.
- Each relay common terminal “COM” are independent, user-friendly access to different signals, each relay are normally closed and normally open with the port.
- Each relay is equipped with motion lights.
- All interfaces can be directly connected through the terminal leads, very convenient.
₹546.00 -
1Hz-50MHz Crystal Oscillator Frequency Counter DIY Kit LED Digital Frequency Tester Meter
- LED display to show the data clearly.
- Measuring Frequency Range: 1Hz~50MHz; Signal Frequency: Max.30V.
- Can measure the oscillation frequency of most commonly used crystals.
- Automatic range conversion without manual switching.
- Programmable addition and subtraction frequency settings, can measure radio transceiver.
- Warranty not applicable for this product
₹390.00 -
5V 8 Channel Relay Module
Features:
- The 8550 transistor drive, drive ability.
- A fixed bolt holes for easy installation.
- It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red)
- Relay control interface by single-chip IO.
- Low-level suction close, high-level release.
- Easy to use, simple 3 line structure.
₹285.005V 8 Channel Relay Module
₹285.00 -
5V WiFi Relay Module v1.0 for ESP8266 ESP01S- IOT Smart Home Remote Control Switch
- Operating Voltage: DC 5V
- Transmission range: the maximum transmission range of 400m (open environment, mobile phone equipped with WIFI module)
- Load capacity: 10A / 250VAC 10A / 30VDC, the relay pulls 100,000 times
- Designed for smart home, internet of thing and other DIY project.
₹225.00 -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 -
4 Channel 12V Relay Module with Optocoupler
- Operating Voltage: 12V DC
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- Freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
- LED Status indicators to indicate the relay ON/OFF status
- Mounting holes provided
₹140.00 -
12V 4 Channel Relay Module
1.Trigger Voltage(VDC):12
2.Trigger Current (MA):20
3.Switching Voltage (VAC):250@10A
4.Switching Voltage (VDC):30@10A
5.Operating Temperature (°C):-40 to 85
6.Opt. Relative Humidity(RH):20% ～ 85%
7.Storage condition (℃):-65 to 125
₹115.0012V 4 Channel Relay Module
₹115.00 -
4 Channel 5V Relay Module
- 5V 4-Channel Relay interface board and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A; DC30V 10A.
- Standard interface that can be controlled directly by microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Indication LED’s for Relay output status.
₹105.004 Channel 5V Relay Module
₹105.00 -
DS1302 Real Time Clock Module (RTC)
Features:-
- Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year with Leap-Year Compensation Valid Up to 2100
- Serial I/O for Minimum Pin Count
- 2.0V to 5.5V Full Operation
- Uses Less than 300nA at 2.0V
- Single-Byte or Multiple-Byte (Burst Mode) Data Transfer for Read or Write of Clock or RAM Data
₹95.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
