-
4 Channel 12V Relay Module with Optocoupler
- Operating Voltage: 12V DC
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- Freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
- LED Status indicators to indicate the relay ON/OFF status
- Mounting holes provided
₹140.00 -
2 Channel 12V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 -
1 Channel 12V Relay Module with Optocoupler
- Maximum Voltage: 5V
- Maximum Current: 10A
- Operating Temperature: -40 to 85°C
- Contact Load: Low Power
- Power Source: DC
- LED Indication of Relay ON
₹39.00 -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 -
2 Channel 5V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 -
1 Channel 5V Relay Module with Optocoupler
1 channel relay board
– Operating Voltage 5V
– Max Current : 20mA
– Relay Contact Current Capacity at AC250V: 10A₹39.00 -
DS1302 Real Time Clock Module (RTC)
Features:-
- Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year with Leap-Year Compensation Valid Up to 2100
- Serial I/O for Minimum Pin Count
- 2.0V to 5.5V Full Operation
- Uses Less than 300nA at 2.0V
- Single-Byte or Multiple-Byte (Burst Mode) Data Transfer for Read or Write of Clock or RAM Data
₹95.00 -
Micro SD Card Reader Module
- Features:-
- Support Micro SD Card (<=2G), Micro SDHC card (<=32G) (high-speed card)
- The level conversion circuit board that can interface level is 5V or 3.3V
- Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
- Communication interface is a standard SPI interface
- 4 M2 screw positioning holes for easy installation
- Size: 4.1 x 2.4cm
₹65.00Micro SD Card Reader Module
₹65.00 - Features:-
-
Laser sensor Module 650nm 6mm 5V 5mW Red Laser
- Voltage: 3.0 V – 5 V.
- Driver: APC circuit.
- Line length: about 135 mm.
- Transmit power: 58mW.
- Operating Current: 40mA.
- Operating Current: 40mA.
- Operating temperature: -36â—¦C ~ 65â—¦C.
₹39.00 -
Dual-axis XY Joystick Module
- Input voltage range: DC 3.3V to 5V, Quality rocker, long life, stable performance
- Two analog outputs, one digital output
- X, y-axis output of the two potentiometers can be read out through the a to d converter
- Cross joystick is a bi-directional 10K resistor, with the rocker in different directions, the tap resistance with the change. This module uses 5V power supply, the original state of X, Y read voltage of 2.5V or so, when pressed with the arrow direction, the read voltage value increases with the maximum to 5V; arrows in the opposite direction to press, read the voltage decreases , The minimum is 0V.
- Package content: 1 joystick module
₹42.00Dual-axis XY Joystick Module
₹42.00 -
12V 4 Channel Relay Module
1.Trigger Voltage(VDC):12
2.Trigger Current (MA):20
3.Switching Voltage (VAC):250@10A
4.Switching Voltage (VDC):30@10A
5.Operating Temperature (°C):-40 to 85
6.Opt. Relative Humidity(RH):20% ～ 85%
7.Storage condition (℃):-65 to 125
₹115.0012V 4 Channel Relay Module
₹115.00 -
12V 2 Channel Relay Module
1.Trigger Voltage(VDC):12
2.Trigger Current (MA):20
3.Switching Voltage (VAC):250@10A
4.Switching Voltage (VDC):30@10A
5.Operating Temperature (°C):-40 to 85
6.Opt. Relative Humidity(RH):20% ～ 85%
7.Storage condition (℃):-65 to 125
₹65.0012V 2 Channel Relay Module
₹65.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
