-
5V 8 Channel Relay Module
Features:
- The 8550 transistor drive, drive ability.
- A fixed bolt holes for easy installation.
- It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red)
- Relay control interface by single-chip IO.
- Low-level suction close, high-level release.
- Easy to use, simple 3 line structure.
₹285.005V 8 Channel Relay Module
₹285.00 -
5V 16 Channel Relay Module with Light Coupling LM2596S Power Supply
Features :
- 5V 16-Channel Relay Module with AC contact capacity of 10A 250V and optocoupler protection.
- Onboard power supply module does not need an external power supply. I / O port driver is active low.
- The module can be used as a microcontroller development board module and also as appliance control, PLC extended output.
- It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
- The 1-16 road can be any full on/off or any road.
- Each relay common terminal “COM” are independent, user-friendly access to different signals, each relay are normally closed and normally open with the port.
- Each relay is equipped with motion lights.
- All interfaces can be directly connected through the terminal leads, very convenient.
₹546.00 -
NE555 Delay Monostable Switch Module with Relay
- Input voltage: DC 12V
- Adjustable time: 0-10 s
- AC Control voltage: 250V/max. 10A
- Max. load: 2200W
₹70.00 -
5V WiFi Relay Module v1.0 for ESP8266 ESP01S- IOT Smart Home Remote Control Switch
- Operating Voltage: DC 5V
- Transmission range: the maximum transmission range of 400m (open environment, mobile phone equipped with WIFI module)
- Load capacity: 10A / 250VAC 10A / 30VDC, the relay pulls 100,000 times
- Designed for smart home, internet of thing and other DIY project.
₹225.00 -
4 Channel 12V Relay Module with Optocoupler
- Operating Voltage: 12V DC
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- Freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
- LED Status indicators to indicate the relay ON/OFF status
- Mounting holes provided
₹140.00 -
2 Channel 12V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 -
1 Channel 12V Relay Module with Optocoupler
- Maximum Voltage: 5V
- Maximum Current: 10A
- Operating Temperature: -40 to 85°C
- Contact Load: Low Power
- Power Source: DC
- LED Indication of Relay ON
₹39.00 -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 -
2 Channel 5V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 -
1 Channel 5V Relay Module with Optocoupler
1 channel relay board
– Operating Voltage 5V
– Max Current : 20mA
– Relay Contact Current Capacity at AC250V: 10A₹39.00 -
12V 4 Channel Relay Module
1.Trigger Voltage(VDC):12
2.Trigger Current (MA):20
3.Switching Voltage (VAC):250@10A
4.Switching Voltage (VDC):30@10A
5.Operating Temperature (°C):-40 to 85
6.Opt. Relative Humidity(RH):20% ～ 85%
7.Storage condition (℃):-65 to 125
₹115.0012V 4 Channel Relay Module
₹115.00 -
12V 2 Channel Relay Module
1.Trigger Voltage(VDC):12
2.Trigger Current (MA):20
3.Switching Voltage (VAC):250@10A
4.Switching Voltage (VDC):30@10A
5.Operating Temperature (°C):-40 to 85
6.Opt. Relative Humidity(RH):20% ～ 85%
7.Storage condition (℃):-65 to 125
₹65.0012V 2 Channel Relay Module
₹65.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
