-
0.96 Inch I2C/IIC 4pin OLED Display Module BLUE
Features of 4 pin 128 x 64 OLED Display
- Â Â Â Super High Brightness (Adjustable)
- Â Â Â Super High Contrast (Adjustable)
- Â Â Â Embedded Driver/Controller
-    Display size: 0.96″
- Â Â Â Resolution radio:128 x 64
- Â Â Â Interface modes: I2C/IIC
- Â Â Â working voltage: 3.3V
- Â Â Â Control Chip: SSD1306
₹165.00 -
1 Channel 12V Relay Module
- The relay high-level pull-in, the module contains current-limiting resistance, a high level can be DC +, microcontroller I / O port can be set high;
- Fault-tolerant design, even if the control line is broken, the relay will not move;
- Power indicator (red), 1 relay status indicator (blue)
- User-friendly interface design, all interfaces can be directly connected through the terminal leads, very convenient
- With four fixing bolt holes, easy to install
₹35.001 Channel 12V Relay Module
₹35.00 -
1 Channel 12V Relay Module with Optocoupler
- Maximum Voltage: 5V
- Maximum Current: 10A
- Operating Temperature: -40 to 85°C
- Contact Load: Low Power
- Power Source: DC
- LED Indication of Relay ON
₹39.00 -
1 Channel 5V Relay Module
- There is a normally open and one normally closed contact.
- The control DC or AC signal, you can control 220V AC load.
- Blue KF301 terminals to the control line is more convenient.
- With the power supply and relay instructions, pull off, disconnect does not shine.
- The module complies with international safety standards, the control area and the load region isolation trench.
₹35.001 Channel 5V Relay Module
₹35.00 -
1 Channel 5V Relay Module with Optocoupler
1 channel relay board
– Operating Voltage 5V
– Max Current : 20mA
– Relay Contact Current Capacity at AC250V: 10A₹39.00 -
1200W DC-DC Boost Module 20A Step-up Boost Convertor 8-60V to 12-80V Adjustable Power Supply
- 1200W DC to DC step-up power supply module for electronic equipment with adjustable power supply module where you can set the output voltage according to device.
- Input and output are designed with screw terminals for convenient wire connection and disconnection.
- Input voltage: 8-60V
- Output voltage: 12-80V continuously adjustable
₹795.00 -
12V 2 Channel Relay Module
1.Trigger Voltage(VDC):12
2.Trigger Current (MA):20
3.Switching Voltage (VAC):250@10A
4.Switching Voltage (VDC):30@10A
5.Operating Temperature (°C):-40 to 85
6.Opt. Relative Humidity(RH):20% ～ 85%
7.Storage condition (℃):-65 to 125
₹65.0012V 2 Channel Relay Module
₹65.00 -
12V 4 Channel Relay Module
1.Trigger Voltage(VDC):12
2.Trigger Current (MA):20
3.Switching Voltage (VAC):250@10A
4.Switching Voltage (VDC):30@10A
5.Operating Temperature (°C):-40 to 85
6.Opt. Relative Humidity(RH):20% ～ 85%
7.Storage condition (℃):-65 to 125
₹115.0012V 4 Channel Relay Module
₹115.00 -
150W DC-DC Boost Converter 10-32V to 12-35V 6A Step-Up Adjustable Power Supply
Features :
- The non-isolated step-up power conversion module
- Onboard LED illuminates when the voltage is applied to the module
- Equips Multi-turn Potentiometer.
- Easy to drive 65W 90W dual-core notebook.
- The output voltage is continuously adjustable on OUT+ and OUT- screw terminals (Output voltage must be greater than input voltage)
₹150.00 -
16×2 Yellow or Green Backlight Alphanumeric Character LCD Display
- 16×2 LCD display Green LED Backlight
- The contrast of the screen can also be controlled by varying the voltage at the contrast control pin
- It is easy to interface with most micro controllers
₹90.00 -
1Hz-50MHz Crystal Oscillator Frequency Counter DIY Kit LED Digital Frequency Tester Meter
- LED display to show the data clearly.
- Measuring Frequency Range: 1Hz~50MHz; Signal Frequency: Max.30V.
- Can measure the oscillation frequency of most commonly used crystals.
- Automatic range conversion without manual switching.
- Programmable addition and subtraction frequency settings, can measure radio transceiver.
- Warranty not applicable for this product
₹390.00 -
2 Channel 12V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
