-
2 Channel 5V Relay Module
- The module using Songle relay control.
- AC voltage 250V, AC current 10A, maximum DC voltage 30V DC current maximum 10A.
- Power indicator (green), Two ways of relay status indicator light (red).
- Using 8550 transistor-driven, strong driving ability.
- Has the fixed bolt hole and easy installation.
₹55.002 Channel 5V Relay Module
₹55.00 -
2 Channel 5V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 -
2.4″ Inch Touch Screen TFT Display Shield
- 2.4″ Touch LCD TFT display module for Arduino
- 240*320 pixels resolution
- Ability to display 262000 different colors
- The shield comes equipped with a microSD card slot.
- SPFD5408 controller with built-in video RAM buffer
₹500.00 -
20×4 Character LCD Module Display Blue Backlight
- 20×4 Character LCD Module Display has Wide viewing angle and high contrast
- Industry-standard HD44780 equivalent LCD controller built-in
- +5V DC LED blue backlight
- Don’t need a separate power supply for the backlight
- Supported 4 or 8-bit parallel interface
- Display 4-line x 20-character
- Operate with 5V DC
- Operating Temperature -20°C to 70°C
- Dot Matrix 5×8 Dots
₹350.00 -
28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver
- Rated voltage: 5V DC
- Reduction Ratio: 64:1
- Step Angle: 5.625° /64
- Frequency: 100Hz
- Self-positioning Torque: >34.3mN.m
- Friction torque: 600-1200 gf.cm
- Pull in torque: 300 gf.cm
₹95.00₹125.0028BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver
₹95.00₹125.00 -
3.5″ Touch Screen LCD Raspberry Pi Display
Features:
- Designed for Raspberry Pi, an ideal alternative solution for HDMI monitor
- Supports all revision of Raspberry Pi (directly-pluggable models)
- Works with Raspbian/Ubuntu directly
- Comes with a full set of screws and nuts for assembly
- 320×480 resolution, better display
- Lightweight and easy to install
₹1,580.00 -
4 Bits Digital Tube LED Display Module With Clock Display
- Driver Chip:Â MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 30 mA
- Display Dimensions: 42x24x12 (LxWxH) mm
₹75.00 -
4 Channel 12V Relay Module with Optocoupler
- Operating Voltage: 12V DC
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- Freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
- LED Status indicators to indicate the relay ON/OFF status
- Mounting holes provided
₹140.00 -
4 Channel 5V Relay Module
- 5V 4-Channel Relay interface board and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A; DC30V 10A.
- Standard interface that can be controlled directly by microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Indication LED’s for Relay output status.
₹105.004 Channel 5V Relay Module
₹105.00 -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 -
4×3 Matrix Membrane Type Keypad -12 Keys
Specifications of 4×3 Matrix Keypad -12 Keys:-
- Length of cable + connector: 93mm
- 7-pin 0.1″ pitch connector
- Weight: 7.5 grams
- Keypad dimensions: 68.5mm x 76.5mm x 1mm
4×3 Matrix Membrane Keypad Features:-
- Ultra-thin design & adhesive backing provides easy integration to any project
- Excellent price-performance ratio
- Easy communication with any microcontroller
- Sticker can peel off for adhesive mounting.
- Used widely in industrial and home electronic equipments, instrument, etc.
- This allows a microcontroller to ‘scan’ the 7 output pins to see which of the 12 buttons is being pressed
₹40.00 -
4×4 Keypad
- Ultra-thin design & adhesive backing provides easy integration to any project.
- Excellent price-performance ratio.
- Easy communication with any microcontroller
- 5 pins 2.54mm pitch connector, 4x 4type 16 keys.
- Sticker can peel off for adhesive mounting.
₹55.004×4 Keypad
₹55.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
