-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 -
4×4 Keypad
- Ultra-thin design & adhesive backing provides easy integration to any project.
- Excellent price-performance ratio.
- Easy communication with any microcontroller
- 5 pins 2.54mm pitch connector, 4x 4type 16 keys.
- Sticker can peel off for adhesive mounting.
₹55.004×4 Keypad
₹55.00 -
4 Channel 12V Relay Module with Optocoupler
- Operating Voltage: 12V DC
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- Freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
- LED Status indicators to indicate the relay ON/OFF status
- Mounting holes provided
₹140.00 -
2 Channel 12V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 -
1 Channel 12V Relay Module with Optocoupler
- Maximum Voltage: 5V
- Maximum Current: 10A
- Operating Temperature: -40 to 85°C
- Contact Load: Low Power
- Power Source: DC
- LED Indication of Relay ON
₹39.00 -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 -
2 Channel 5V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 -
1 Channel 5V Relay Module with Optocoupler
1 channel relay board
– Operating Voltage 5V
– Max Current : 20mA
– Relay Contact Current Capacity at AC250V: 10A₹39.00 -
L298N 2A Current Motor Driver Board
- Lo Logical voltage:Â 5V
- Drive voltage: 5V-35V
- Logical current:Â 0-36mA
- Drive current: 2A (max. single bridge)
- Max power:Â 25W
- Dimensions:Â 44 x 44 x 28 (LxWxH)mm
- Weight:Â 26 gm
₹99.00 -
L293D Motor Driver Board
- The driver two holes of 3 mm dia.
- Male burg-stick connectors for supply, ground and input connection.
- Screw terminal connectors for easy motor connection.
- High noise immunity inputs.
₹45.00L293D Motor Driver Board
₹45.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
