-
L298N 2A Current Motor Driver Board
- Lo Logical voltage:Â 5V
- Drive voltage: 5V-35V
- Logical current:Â 0-36mA
- Drive current: 2A (max. single bridge)
- Max power:Â 25W
- Dimensions:Â 44 x 44 x 28 (LxWxH)mm
- Weight:Â 26 gm
₹99.00 -
4 Channel 5V Relay Module
- 5V 4-Channel Relay interface board and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A; DC30V 10A.
- Standard interface that can be controlled directly by microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Indication LED’s for Relay output status.
₹105.004 Channel 5V Relay Module
₹105.00 -
12V 4 Channel Relay Module
1.Trigger Voltage(VDC):12
2.Trigger Current (MA):20
3.Switching Voltage (VAC):250@10A
4.Switching Voltage (VDC):30@10A
5.Operating Temperature (°C):-40 to 85
6.Opt. Relative Humidity(RH):20% ～ 85%
7.Storage condition (℃):-65 to 125
₹115.0012V 4 Channel Relay Module
₹115.00 -
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
Features :
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
₹116.00 -
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
Features :
- Microstep resolutions:Â full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Adjustable current control lets you set the maximum current output with a potentiometer. Hence lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- 45Â V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
- Can interface directly with 3.3Â V and 5Â V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- 4-layer, 2Â oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
₹126.00 -
MAX7219 Dot Led Matrix Module MCU Control LED Display Module
- Driver Chip:Â MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 320 mA
- Display Dimensions: 32x32x6 (LxWxH) mm
- PCD Dimensions: 50×32 (LxW) mm
₹130.00 -
4 Channel 12V Relay Module with Optocoupler
- Operating Voltage: 12V DC
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- Freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
- LED Status indicators to indicate the relay ON/OFF status
- Mounting holes provided
₹140.00 -
150W DC-DC Boost Converter 10-32V to 12-35V 6A Step-Up Adjustable Power Supply
Features :
- The non-isolated step-up power conversion module
- Onboard LED illuminates when the voltage is applied to the module
- Equips Multi-turn Potentiometer.
- Easy to drive 65W 90W dual-core notebook.
- The output voltage is continuously adjustable on OUT+ and OUT- screw terminals (Output voltage must be greater than input voltage)
₹150.00 -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 -
Motor Driver Module TA6586 Based
Features:
- Heavy-duty screw terminal for the input.
- Can be connected directly to the 433MHz receiver output.
- Can drive up to 5A of current.
- Drives 2 motors.
₹165.00Motor Driver Module TA6586 Based
₹165.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
