-
28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver
- Rated voltage: 5V DC
- Reduction Ratio: 64:1
- Step Angle: 5.625° /64
- Frequency: 100Hz
- Self-positioning Torque: >34.3mN.m
- Friction torque: 600-1200 gf.cm
- Pull in torque: 300 gf.cm
₹95.00₹125.0028BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver
₹95.00₹125.00 -
MAX7219 Dot Led Matrix Module MCU Control LED Display Module
- Driver Chip:Â MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 320 mA
- Display Dimensions: 32x32x6 (LxWxH) mm
- PCD Dimensions: 50×32 (LxW) mm
₹130.00 -
8X8 Mini Dot Matrix LED Display
- Easy to Install on Breadboard
- Bright LED lights
- Compact Design.
- LED Size: 3mm
- Configuration: Common Cathode
₹45.00 -
-
4 Bits Digital Tube LED Display Module With Clock Display
- Driver Chip:Â MAX7219
- Input Voltage: 3.7 to 5.3 V
- Input Current: 30 mA
- Display Dimensions: 42x24x12 (LxWxH) mm
₹75.00 -
20×4 Character LCD Module Display Blue Backlight
- 20×4 Character LCD Module Display has Wide viewing angle and high contrast
- Industry-standard HD44780 equivalent LCD controller built-in
- +5V DC LED blue backlight
- Don’t need a separate power supply for the backlight
- Supported 4 or 8-bit parallel interface
- Display 4-line x 20-character
- Operate with 5V DC
- Operating Temperature -20°C to 70°C
- Dot Matrix 5×8 Dots
₹350.00 -
16×2 Yellow or Green Backlight Alphanumeric Character LCD Display
- 16×2 LCD display Green LED Backlight
- The contrast of the screen can also be controlled by varying the voltage at the contrast control pin
- It is easy to interface with most micro controllers
₹90.00 -
XL6009 boost converter DC-DC Booster Step Up Power supply module
- The performance is much higher than LM2577.
- Non-isolated Boost converter.
- It has a non-synchronous rectifier.
- Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range;
- Low ultra wide output voltage 5 v ~ 35 v;
₹95.00 -
DS1302 Real Time Clock Module (RTC)
Features:-
- Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year with Leap-Year Compensation Valid Up to 2100
- Serial I/O for Minimum Pin Count
- 2.0V to 5.5V Full Operation
- Uses Less than 300nA at 2.0V
- Single-Byte or Multiple-Byte (Burst Mode) Data Transfer for Read or Write of Clock or RAM Data
₹95.00 -
Micro SD Card Reader Module
- Features:-
- Support Micro SD Card (<=2G), Micro SDHC card (<=32G) (high-speed card)
- The level conversion circuit board that can interface level is 5V or 3.3V
- Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
- Communication interface is a standard SPI interface
- 4 M2 screw positioning holes for easy installation
- Size: 4.1 x 2.4cm
₹65.00Micro SD Card Reader Module
₹65.00 - Features:-
-
LM2596 DC Step Down Buck Converter Power Supply Module
- Input voltage: 4.5-40V,
- Output voltage: (3-35V) continuously adjustable (recommended load debugging).
- Minimum pressure: 1.5V
- Output current: rated current 2A, 3A maximum
- Output Power: 15W maximum
₹55.00 -
Laser sensor Module 650nm 6mm 5V 5mW Red Laser
- Voltage: 3.0 V – 5 V.
- Driver: APC circuit.
- Line length: about 135 mm.
- Transmit power: 58mW.
- Operating Current: 40mA.
- Operating Current: 40mA.
- Operating temperature: -36â—¦C ~ 65â—¦C.
₹39.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
