-
LDR (Light Dependent Resistor) Sensor 3mm
- Diameter: 3mm
- No. of Pins: 2
- Type of Mounting: PCB Through Hole
- Maximum Operating Temperature: +800°C (Approx.)
- Dark resistance:1-20 Mohm
₹4.00₹7.00LDR (Light Dependent Resistor) Sensor 3mm
₹4.00₹7.00 -
LDR (Light Dependent Resistor) Sensor 5mm high quality
- Diameter: 5mm
- No. of Pins: 2
- Type of Mounting: PCB Through Hole
- Maximum Operating Temperature: +800°C (Approx.)
- Dark resistance:1-20 Mohm
₹9.00 -
Infrared IR Transmitter and Receiver (Photo-diode) Pair
Features:
- IR LED (TSFF5210)
- Package type: leaded
- Dimensions : 5mm
- Leads with stand-off
- Peak wavelength: λp = 870 nm
- High reliability
- High radiant power
- High radiant intensity
- Angle of half intensity: = ± 10°
- Low forward voltage
- Suitable for high pulse current operation
- High modulation bandwidth: fc = 24 MHz
- Good spectral matching with Si photodetectors
- IR Photodiode (BPV10NF)
- Package type: leaded
- Dimensions : 5mm
- Leads with stand-off
- Radiant sensitive area (in mm2): 0.78
- High radiant sensitivity
- Daylight blocking filter matched with 870 nm to 890 nm emitters
- High bandwidth: > 100 MHz at VR = 12 V
- Fast response times
- Angle of half sensitivity: ± 20°
₹10.00 - IR LED (TSFF5210)
-
SW420 Tilt Ball switch 2801 ball sensor
- Operating voltage: 5V
- Contact Resistance: < 10 Ohms
- Trigger Angle: 15°
- Pins have no polarity
- This series of products is a ball sensor switch, up and down, or. Tilt over 15 degrees is conductive
- The series switch is normally open at rest (OFF) state, when the external force to achieve the corresponding flip, or at a proper angle of tilt, trigger switch.
- The trigger sensitivity of the inductive switch is very high
- Fully sealed package, waterproof, dustproof.
₹10.00 -
TSOP IR Receiver for ARDUINO AVR
- Very low supply current
- Photo-detector and preamplifier in one package
- Internal filter for PCM frequency
- Improved shielding against EMI
- Supply voltage: 2.5 V to 5.5 V
- Improved immunity against ambient light
₹12.00 -
Voltage Detection Sensor Module 25V
Features :
- Output Interface: “+ ” connected 5/3.3V, “-” connected GND, “s” connected Arduino AD pins
- DC input interface: red terminal positive with VCC, negative with GND
- You can also use the IICLCD1602 LCD to display voltage.
- By 3P connector, connect this module with the expansion of board Arduino, not only makes it easier for you to detect voltage battery.
₹13.00 -
-
Infrared (IR) Proximity/Obstacle Detecting Sensor Module
- BUY IN ORIGINAL FROM OLatus or OL ELECTRONICS STORE ONLY. WE WILL NOTE SUPPORT FAKE MODULES
- COMPATIBLE WITH ARDUINO, RASPBERRY PI, ARM, AVR, PIC, 8051, etc.
- Useful for various Robotic Applications, Object Detection, Visitor Counter, etc
- Operating Voltage : 5V DC Digital Output : logic one (+3.5V DC) logic zero (0V DC)
₹18.00₹29.00 -
Photosensitive Light Sensor ( LDR Sensor Board)
- Operating voltage 3.3V-5V
- Signal output indicator light
- Able to detect ambient brightness and light intensity Adjustable sensitivity
₹18.00₹35.00Photosensitive Light Sensor ( LDR Sensor Board)
₹18.00₹35.00 -
IR Sensor Module Infrared based for Proximity/Object Detection
- Power: 3.3V ~ 5V
- Mounting holes size: 3mm
- Detection range: 2cm ~ 30cm (depending on the obstacle’s color, farthest for white)
- Detection angle: 35°
- LM393 voltage comparator
- Recommended environment: indoor, to avoid the sunshine effect
₹19.00₹24.00 -
Flame Sensor infrared Receiver Ignition source detection module
- Output Channel: 1
- Power Supply: 3.3/5V
- Built in a potentiometer for sensitivity control.
- Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO.
- Detection angle about 60 degrees, the flame spectrum especially sensitive.
- The flame of the most sensitive sensors flame, the regular light is also a response, generally used for fire alarm purposes.
₹19.00 -
TTP223B Digital Capacitive Touch Sensor Module
- Low power consumption.
- Power supply for 2 ~ 5.5V DC
- Can replace the traditional touch of a button, touch area.
- Four m2 screws positioning holes for easy installation, power indicator green led, power on the right that is shiny.
- Control interface : A total of three pins (gnd, vcc, sig), gnd to ground , vcc is the power supply , sig digital signal output pin.
₹22.00₹35.00TTP223B Digital Capacitive Touch Sensor Module
₹22.00₹35.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
