-
5V Relay Switch PCB Mount
- Trigger Voltage: 5V Relay Switch PCB Mount
- Trigger Current : 20 mA
- Maximum Switching Voltage:Â 250VAC@10A; 30VDC @10A
- Single Pole Double Throw (SPDT) Configuration
- Power supply indicator lamp
₹12.00 (Price is Exclusive of GST)5V Relay Switch PCB Mount
₹12.00 (Price is Exclusive of GST) -
1 Channel 5V Relay Module
- There is a normally open and one normally closed contact.
- The control DC or AC signal, you can control 220V AC load.
- Blue KF301 terminals to the control line is more convenient.
- With the power supply and relay instructions, pull off, disconnect does not shine.
- The module complies with international safety standards, the control area and the load region isolation trench.
₹35.00 (Price is Exclusive of GST)1 Channel 5V Relay Module
₹35.00 (Price is Exclusive of GST) -
1 Channel 5V Relay Module with Optocoupler
1 channel relay board
– Operating Voltage 5V
– Max Current : 20mA
– Relay Contact Current Capacity at AC250V: 10A₹35.00 (Price is Exclusive of GST)1 Channel 5V Relay Module with Optocoupler
₹35.00 (Price is Exclusive of GST) -
2 Channel 5V Relay Module
- The module using Songle relay control.
- AC voltage 250V, AC current 10A, maximum DC voltage 30V DC current maximum 10A.
- Power indicator (green), Two ways of relay status indicator light (red).
- Using 8550 transistor-driven, strong driving ability.
- Has the fixed bolt hole and easy installation.
₹55.00 (Price is Exclusive of GST)2 Channel 5V Relay Module
₹55.00 (Price is Exclusive of GST) -
2 Channel 5V Relay Module
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 (Price is Exclusive of GST)2 Channel 5V Relay Module
₹65.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module
- 5V 4-Channel Relay interface board and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A; DC30V 10A.
- Standard interface that can be controlled directly by microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Indication LED’s for Relay output status.
₹105.00 (Price is Exclusive of GST)4 Channel 5V Relay Module
₹105.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Mechanical Hardware Tools and Accessories
- Power Supply and Prototypes
- Robotics and Hobbies
- Sensors
- Scientific Tools and Equipments
- Other Tools and Equipment’s
- Bulk/Wholesale
