-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST)
-
Pro-Range 12V 60 RPM Johnson Geared DC Motor – Grade A Quality-Encoder Compatible
- Base Motor RPM: 18000
- Operating Voltage: 6-18 V
- Rated Voltage: 12 V
- Rated Torque: 157.6 N-cm
- Stall Torque: 850 N-cm
- Gearbox Dimensions: 29×37 (LxW) mm
₹435.00 (excl. GST) -
Pro-Range INR 18650 11.1V 2000mAh 3C 3S1P Li-Ion Battery Pack with DC Jack Male & Female
- Nominal Capacity (mAh): 2000
- Nominal Voltage (v): 11.1
- Max Charging Voltage (v): 12.6
- Charge Port: DC Female
- Discharge Port: DC Male
₹840.00 (excl. GST) -
₹1,246.00 (excl. GST)
Orange 7.4V 2200mAh 30C 2S Lithium Polymer Battery Pack
₹1,246.00 (excl. GST) -
HX711 Dual-Channel 24 Bit Precision A/D weight Pressure Sensor
- Output Sensitivity: 1.0 ± 0.1 mV / V.
- Two selectable differential input channels.
- On-chip active low noise PGA with the selectable gain of 32, 64 and 128.
- On-chip oscillator requiring no external component with optional external crystal.
- On-chip power-on-reset.
- Measurement Resolution: 24 bit.
₹43.00 (excl. GST)HX711 Dual-Channel 24 Bit Precision A/D weight Pressure Sensor
₹43.00 (excl. GST) -
Official Raspberry Pi M.2 HAT+
- Fast Data Transfer: Achieve speeds of up to 450 Mbytes/s with the 4 Gbits/s PCIe 2.0 interface for NVMe SSDs and PCIe accessories.
- Seamless Compatibility: Fully compliant with HAT+ specification for easy integration with Raspberry Pi 5.
- Plug-and-Play: Automatically detected by the latest Raspberry Pi software and firmware.
- Easy Installation: Comes with a 16mm stacking header, spacers, and screws for convenient setup with the Active Cooler in place.
₹978.00 (excl. GST)Official Raspberry Pi M.2 HAT+
₹978.00 (excl. GST) -
Tactile Push Button Switch 6x6x5 (Pack of 10)
- Ideal for Through-hole applications.
- Shaft Shape: Round
- Used in the fields of electronic products, household appliances and more.
-
This light touch switch is waterproof, prevent oil, anti-pollution, anti-static interference.
-
High precision mechanism design offers acute operation and long service life.
-
Compact and lightweight, easy to carry and dismantling.
-
Good electrical conductivity.
₹17.00 (excl. GST)Tactile Push Button Switch 6x6x5 (Pack of 10)
₹17.00 (excl. GST) -
GY-271 HMC5883L 3-axis Electronic Compass Module
GY-271 HMC5883L 3-axis
- 3-axis magnetic electronic compass.
- Precise heading information.
- Operating Voltage: 3 -5 V DC.
- Driver Chip: HMC5883L.
- Communication: I2C protocol.
- Measuring range: ± 1.3-8 Gauss.
₹118.00 (excl. GST)GY-271 HMC5883L 3-axis Electronic Compass Module
₹118.00 (excl. GST) -
MPU-6050 3-Axis Accelerometer and Gyro Sensor
- Chip built-in 16bit AD converter, 16-bit data output
- Driver Chip: MPU6050
- Operating Voltage: 3-5V DC
- Communication: I2C/IIC Protocol
- Gyro Range: ± 250, 500, 1000, 2000 °/s
- Accelerometer Range: ± 2 ± 4 ± 8 ± 16 g
₹158.00 (excl. GST)MPU-6050 3-Axis Accelerometer and Gyro Sensor
₹158.00 (excl. GST) -
SpeedyBee TX800 5.8GHz Video Transmitter
- Model: TX800
- Frequency Channel: 5.8GHz 48CH
- Video input impedance: 75 Ohm
- Antenna Connector: MMCX
₹2,800.00 (excl. GST)SpeedyBee TX800 5.8GHz Video Transmitter
₹2,800.00 (excl. GST) -
50kg Half-bridge Experiments Body Scale Load Cell Sensor
- Capacity (Kg): 50.
- Output Sensitivity (mv/v): 1.0±0.1.
- Nonlinearity (%FS): 0.03.
- Repeatability (%FS): 0.03.
- Input Resistance (Ω): 1000.
- Insulation Resistance (MΩ): ≥5000.
₹27.00 (excl. GST)50kg Half-bridge Experiments Body Scale Load Cell Sensor
₹27.00 (excl. GST) -
Official Raspberry Pi 5 Camera FPC Cable – 200mm
- FPC Cable Type: Camera Cable
- Length: 200 mm
₹83.00 (excl. GST)Official Raspberry Pi 5 Camera FPC Cable – 200mm
₹83.00 (excl. GST) -
GT2 Timing Belt 400mm Width-6mm Closed-Loop Rubber Belt for 3D Printer
- Pitch: 2mm
- Material: Neoprene Rubber With Fiberglass Core
- Width: 6mm
- Total Length: 400mm
- Belt Height: 1.52 mm
- Tooth Height: 0.76mm
- Shape: Closed Loop
₹66.00 (excl. GST)GT2 Timing Belt 400mm Width-6mm Closed-Loop Rubber Belt for 3D Printer
₹66.00 (excl. GST)
