-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹638.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹638.00(Price is Exclusive of GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹264.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹264.00 (Price is Exclusive of GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST) -
ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (Price is Exclusive of GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (Price is Exclusive of GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹207.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹207.00 (Price is Exclusive of GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)
-
Samsung INR 21700 50S 22.2 V 20000 mAh 6s4p 140A/180A Discharge Li-ion EFT Agriculture Drone Battery Pack
- Nominal Capacity (in mAh): 20000
- Nominal Voltage (in V): 22.2
- Nominal Wattage in (Wh): 444
- Max Charge Voltage (V):25.2
₹13,884.00 (Price is Exclusive of GST)Samsung INR 21700 50S 22.2 V 20000 mAh 6s4p 140A/180A Discharge Li-ion EFT Agriculture Drone Battery Pack
₹13,884.00 (Price is Exclusive of GST) -
Pro-Range INR 21700 P42A 22.2V 16800mAh 6S4P 150A/190A Discharge Li-ion Drone Battery Pack
- Nominal Capacity (mAh): 16800
- Nominal Voltage (v): 22.2
- Max Charging Voltage (v): 25.2
- Charge Port: 7 Pin JST XH
- Discharge Port: Amass XT90 AS
₹14,219.00 (Price is Exclusive of GST)Pro-Range INR 21700 P42A 22.2V 16800mAh 6S4P 150A/190A Discharge Li-ion Drone Battery Pack
₹14,219.00 (Price is Exclusive of GST) -
Anycubic I3 MEGA S – FDM 3D Printer
Features:
Printing Platform: Strong adhesive when platform’s hot and easy to remove when cool down.
Filament Sensor: Provides better printing experience of flexible
Fast Assembly: Only need to install 8 screws and connect 3 wires before the first print.
Rigid Metal Frame: The structure is very stable which could reduce the body shake druing printing and improve the printing quality
Suspended Filament Rack: One-piece hanging design, simple and beautiful. The feeding of filament is smoother and the storage of filament is more convenint.₹14,500.00 (Price is Exclusive of GST)Anycubic I3 MEGA S – FDM 3D Printer
₹14,500.00 (Price is Exclusive of GST) -
Quadcopter Drone DIY Kit – V1
- Built from quality glass fiber and polyamide nylon.
- Integrated PCB connections for direct soldering of your ESCs
- Pre-threaded brass sleeves for all of the frame bolts.
- Colored arms for orientation to keep you flying in the right direction.
- Large mounting tabs on main frame bottom plate for easy camera mounting.
- Easy assembly.
₹15,000.00 (Price is Exclusive of GST)Quadcopter Drone DIY Kit – V1
₹15,000.00 (Price is Exclusive of GST) -
Quadcopter Drone DIY Kit – V2
Drone DIY Kit Package Contents:
1 x F450 Quadcopter Frame
1 x Flysky i6 Radio Transmitter and Receiver with programmer
4 x 30A ESC
4 x A2212 1000/1400 KV Brushless Motor
1 x Naze 32 Flight Control Board
4 x 1045 (2CW+2CCW) Black Propeller
1 x Lipo Battery ChargerFeatures:
F450 Frame based Quadcopter Kit
Includes 30A ESC for speed control and Lipo battery Charger
Flight Control board Naze 32/ KK 2.1.5
Flysky i6 Radio controller transmitter receiver wireless
Includes Brushless motors and Propellers₹15,000.00 (Price is Exclusive of GST)Quadcopter Drone DIY Kit – V2
₹15,000.00 (Price is Exclusive of GST) -
SDS1000 Series Economical Digital Oscilloscope
- Supports multi-language display and embedded help
- Screensaver from 1 minute to 5 hours
- Digital filter and waveform recorder function
- Shortcut storage function key
- 7-inch TFT-LCD display with 800 * 480 resolution
₹15,000.00 (Price is Exclusive of GST)SDS1000 Series Economical Digital Oscilloscope
₹15,000.00 (Price is Exclusive of GST) -
Herewin 22.2V 16000mAh 25C 6S Lithium Polymer Battery Pack
- 16,000mAh capacity for long flight times
- 6S configuration (22.2V) for high-power systems
- 25C discharge rate for stable power
- Durable and lightweight
- Safe with built-in protection
₹15,098.00 (Price is Exclusive of GST)Herewin 22.2V 16000mAh 25C 6S Lithium Polymer Battery Pack
₹15,098.00 (Price is Exclusive of GST) -
Pro-Range INR 21700 P45B 14.8V 22500mAh 4S5P 180A/225A Discharge Li-ion Drone Battery Pack
- Nominal Capacity (mAh): 22500
- Nominal Voltage (v): 14.8
- Max Charging Voltage (v): 16.8
- Charge Port: 5 Pin JST XH
- Discharge Port: Amass XT90 AS
₹15,336.00 (Price is Exclusive of GST)Pro-Range INR 21700 P45B 14.8V 22500mAh 4S5P 180A/225A Discharge Li-ion Drone Battery Pack
₹15,336.00 (Price is Exclusive of GST) -
Pro- Range 14.8V 16000mAh 35C 4S Lithium Polymer Battery Pack
- Model No: Pro- Range 16000 4S
- Voltage: 14.8V
- Max Continuous Discharge: 35C
- Balance Plug: JST-XH
- Discharge Plug: XT90s
₹15,404.00 (Price is Exclusive of GST)Pro- Range 14.8V 16000mAh 35C 4S Lithium Polymer Battery Pack
₹15,404.00 (Price is Exclusive of GST) -
Ender 3 FDM 3D Printer
Features
- Easy and Quick Assembly: It comes with several assembled parts, you only need about 2 hours to assemble 20 nuts well.
- Â Advanced Extruder Technology: Upgraded extruder greatly reduces plugging risk and bad extrusion; V-Shape with POM wheels makes it move noiseless, smoothly, and durable.
-  Safety Protected Power Supply: Only needs 5 minutes for the hotbed to reach 110℃.
- Â It is a great project for middle school and high school-aged students. The perfect gift to spark a lifelong love for science and engineering, and provide a deeper understanding of machinery and robotics.
-
Max Print Speed : 80mm/s Auto Levelling : NA Print Bed Removeable : NA Supported files : STL，OBJ，G-Code Camera : NA Connectivity : USB or SD offline
₹15,436.00 (Price is Exclusive of GST)Ender 3 FDM 3D Printer
₹15,436.00 (Price is Exclusive of GST) -
Ender-3+ PLA White
- Easy and Quick Assembly: It comes with several assembled parts, you only need about 2 hours to assemble 20 nuts well.
- Â Advanced Extruder Technology: Upgraded extruder greatly reduces plugging risk and bad extrusion; V-Shape with POM wheels makes it move noiseless, smoothly, and durable.
-  Safety Protected Power Supply: Only needs 5 minutes for the hotbed to reach 110℃.
- Â It is a great project for middle school and high school-aged students. The perfect gift to spark a lifelong love for science and engineering, and provide a deeper understanding of machinery and robotics.
Modeling Technology : FDM（Fused Deposition Modeling） Printing Size : 220x220x250mm Printing Speed : 180mm/s Filament : 1.75mm PLA, TPU, ABS Working Mode : Online or SD offline Filament : White ₹15,460.00 (Price is Exclusive of GST)Ender-3+ PLA White
₹15,460.00 (Price is Exclusive of GST) -
Tattu 22.2V 25C 6s 22000mAh LiPo Battery pack with XT90-S Anti Spark Plug for UAV
- Capacity: 22000mAh
- Voltage: 22.2V
- Discharge Rate: 25C
- Max Burst Discharge Rate: 50C
- Balancer Connector Type: JST-XHR
₹15,576.00 (Price is Exclusive of GST)Tattu 22.2V 25C 6s 22000mAh LiPo Battery pack with XT90-S Anti Spark Plug for UAV
₹15,576.00 (Price is Exclusive of GST)
