-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
- “1K ohm Resistor (Pack of 5)” already exists in your wishlist
-
3D Pen Professional for 3D Printing Drawing Pen with 3 x 1.75mm ABS/PLA Filament
- The 3D printing pen has an ergonomic design that makes it comfortable for users.
- The 3D pen is a perfect gift for kids because it is safe and eco-friendly.
- The 3D pen for professionals is compatible with both 1.75mm ABS & PLA Filament.
- It features a Fast boot setup in just 30 seconds. You can draw and create quickly.
- This 3D printing pen is perfect for working professionals like architects, designers and model makers.
₹890.00 (excl. GST)3D Pen Professional for 3D Printing Drawing Pen with 3 x 1.75mm ABS/PLA Filament
₹890.00 (excl. GST) -
₹865.00 (excl. GST)Sunflower kit in persuit of light (school science kit)
₹865.00 (excl. GST) -
BMS 24V 7S 20A Daly Waterproof BMS for Li-ion Cell (NMC) 25.9V
Features :
- Strong load ability, constant discharge current 10A~250A , use high voltage resistance, low inner resistance power Mosfet. The heat sink will greatly help cooling.
- IC itself has power balancing function. The circuit is simple and reliable.
- Typical voltage detection for each cell. So each battery will be prevented over charged or over discharged. Over current and short circuit protection function is very reliable. long time short circuit of the load won’t affect the PCB and the battery. Temperature protection during charging and discharging.
- Extreme low power consumption. the consumption of the whole device is less than 50uA.
- PCB use high anti-corrosion, high water resistance, high impedance ESD conformal coating.
₹850.00 (excl. GST)BMS 24V 7S 20A Daly Waterproof BMS for Li-ion Cell (NMC) 25.9V
₹850.00 (excl. GST) -
Mini Sewing Machine – JYSM-202A
-Mini sewing machine offers double threads and perfect control of points
-Best view and more convenient in cutting the thread
-Small size, lightweight and with exquisite finish
-Equipped with a light lamp and a wire cutter, easy to cut the wires
-A large coil can be used with a rewind device for easy replacement of the bottom bobbin₹850.00₹950.00(excl. GST)Mini Sewing Machine – JYSM-202A
₹850.00₹950.00(excl. GST) -
3D Printer Filament – Multicolor PLA 1.75MM
- It is fed into the FDM 3D printer.
- It is extruded and deposited by an extrusion head onto a build platform where it cools.
- The process is continuous, building up layers to create the model.
₹850.00 (excl. GST)3D Printer Filament – Multicolor PLA 1.75MM
₹850.00 (excl. GST) -
₹850.00 (excl. GST)
W5100 Network Expansion Board Ethernet Shield
₹850.00 (excl. GST) -
Arduino Mega 2560 R3 with USB Cable Compatible with Arduino
- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 256 KB of which 8 KB used by bootloader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
- USB Host Chip: MAX3421E
- Length:101.98mm/4.01in
- Width:53.63mm/2.11in
- Height:15.29mm/0.60in
₹850.00₹1,475.00(excl. GST)Arduino Mega 2560 R3 with USB Cable Compatible with Arduino
₹850.00₹1,475.00(excl. GST) -
SeeedStudio Grove GSR sensor
SeeedStudio
Features:
- Detects conductance of the skin
- Finger Straps for electrodes
₹840.00 (excl. GST)SeeedStudio Grove GSR sensor
₹840.00 (excl. GST) -
12V 3.5A 4000ml/min Liquid Diaphragm Pump
Features:
- Self-Priming
- Low Power Consumption
- Long Life
- Can Run in Dry Condition
₹835.00 (excl. GST)12V 3.5A 4000ml/min Liquid Diaphragm Pump
₹835.00 (excl. GST) -
3S 100A 12.6V Li-ion Lithium 18650 Battery BMS PCM Protection Board with Balance
- Charging voltage: 12.6V-13V
- Size: 70*60*8.5mm
- Over-discharge voltage range: 2.5±0.05v
- Upper limit working current: 100A (pay attention to heat dissipation)
- Working temperature: -40~+50°C
- Effective life: more than 30,000 hours
₹830.00 (excl. GST)3S 100A 12.6V Li-ion Lithium 18650 Battery BMS PCM Protection Board with Balance
₹830.00 (excl. GST) -
NEEMA 17-JK42HS48-1684-0.44N-m D Type 5.5Kg
Features :
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
₹825.00 (excl. GST)NEEMA 17-JK42HS48-1684-0.44N-m D Type 5.5Kg
₹825.00 (excl. GST) -
BMS 8S 24V 20A DALY Lifepo4 Battery Management System
- Model: 8S 24V 20A
- Battery Type: Lithium Battery
- No.of cells in series: 8s
- Discharge Current: 20A
- Charge Current: 10A
₹800.00 (excl. GST)BMS 8S 24V 20A DALY Lifepo4 Battery Management System
₹800.00 (excl. GST)
