-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
820k ohm 1 Watt Resistor (Pack of 5)
Features-
Resistance:Â 820K Ohm,
Power Rating:Â 1 Watt,
Approximate Maximum Current:Â 1.1mA
₹8.00 (excl. GST)820k ohm 1 Watt Resistor (Pack of 5)
₹8.00 (excl. GST) -
84-096-23 127mm-5 Needle Nose Miniature Plier
- Long tempered jaws for working in hard to reach areas
- Forged steel construction
- Rust resistant finish
- Double dipped handle for comfort | Meets or exceeds ANSI standards
₹400.00 (excl. GST)84-096-23 127mm-5 Needle Nose Miniature Plier
₹400.00 (excl. GST) -
8mm Bore Inner Ball Mounted Pillow Block Insert Bearing KP08
8mm Bore Inner Ball Mounted
- Type: KP08
- Material: zinc alloy
- Bore Diameter:8mm
- Mounting Hole Diameter: 5 mm
- Durable with high precision
- Can withstand great weight
₹83.00 (excl. GST)8mm Bore Inner Ball Mounted Pillow Block Insert Bearing KP08
₹83.00 (excl. GST) -
8x19x6 698ZZ Stainless Steel Shielded Miniature Bearings (4Pcs)
The shield protects the working parts of the bearing from environmental debris that may be introduced and could reduce the ball bearing speed and lifespan. Rolling bearings are used in a range of applications from agricultural machinery to conveying equipment, robotics, dental equipment, elevators, rolling mills, ship rudder shafts, and aggregate crushers, among others.
₹160.00 (excl. GST)8x19x6 698ZZ Stainless Steel Shielded Miniature Bearings (4Pcs)
₹160.00 (excl. GST) -
8X8 Mini Dot Matrix LED Display
- Easy to Install on Breadboard
- Bright LED lights
- Compact Design.
- LED Size: 3mm
- Configuration: Common Cathode
₹45.00 (excl. GST)8X8 Mini Dot Matrix LED Display
₹45.00 (excl. GST) -
9 Volt Power Adaptor Single Pin 1 Amps
- Material: Plastic
- Colour: Black
- Dimensions (L x B x H): 6.5 cm x 3.5 cm x 10 cm
- Weight: 120 g
- Warranty: 6 Months Seller Warranty on Manufacturing Defects
- Care Instructions: Check specifications before use
₹90.00 (excl. GST)9 Volt Power Adaptor Single Pin 1 Amps
₹90.00 (excl. GST) -
9v Battery Snap Connector with DC Jack
- Excellent material
- It is an environmental 9V battery buckle
- The Cable Length: 12cm Approx.
- Convenient for connecting a battery to your application.
- Save power and protect the environment
- Good electrical conductivity and comfortable sense of touch
₹9.00 (excl. GST)9v Battery Snap Connector with DC Jack
₹9.00 (excl. GST) -
9v Battery Snap Connector without DC Jack
- Excellent material
- It is an environmental 9V battery buckle
- The Cable Length: 12cm Approx.
- Convenient for connecting a battery to your application.
- Save power and protect the environment
- Good electrical conductivity and comfortable sense of touch
₹6.00 (excl. GST)9v Battery Snap Connector without DC Jack
₹6.00 (excl. GST) -
9V Watt Battery
- Constant 9V Output till lasts.
- Metal Jacket Body.
- Easy to install and Replace
- Pack of 2 Battery.
₹18.00 (excl. GST)9V Watt Battery
₹18.00 (excl. GST) -
A4988 driver Stepper Motor Driver
Features :
- Automatic current decay mode detection/choice.
- Mixed with slow current decay mode.
- The low power dissipation of synchronous rectifier.
- Internal UVLO(ultra voltage lockout).
- Crossover current protection.
- Thermal shutdown circuit.
- Ground fault protection.
- Loading and short circuit protection.
- The optional five-step mode: full, 1/2, 1/4, 1/8 and 1/16.
₹78.00 (excl. GST)A4988 driver Stepper Motor Driver
₹78.00 (excl. GST) -
A4988 Stepper Motor Driver Controller Board- RED
Controller Board
- Compact size, easy to install and use.
- All jumpers hit the ON position to indicate 16 subdivisions (4988) or 32 subdivisions (8825).
- Jm connection motor: Jv Connects 5V and 12V-24V Power Supply.
- E /S /D /G of Jc corresponds to Enable /Step /Dir /Gnd driving signal output on the connection respectively.
₹49.00 (excl. GST)A4988 Stepper Motor Driver Controller Board- RED
₹49.00 (excl. GST) -
ABS Plastic Landing Gear for Quadcopter (Pack of 4) – Made in INDIA
ABS Plastic Landing Gear for Quadcopter
- Color: Black
- Material: ABS Plastic
- Length: ~190mm
- Ground Clearance: 150 mm
- Compatibility: Q450 and S500 Frames
- Weight: 75 gm (total of 4)
₹132.00 (excl. GST)ABS Plastic Landing Gear for Quadcopter (Pack of 4) – Made in INDIA
₹132.00 (excl. GST)
