-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
Aluminum Brazing Wire Dia 2.0 (5 Meter Flux Cored Aluminum Brazing Wire)-pack of 3
Aluminum Brazing Wire
It significantly reduces the leakage problems found after brazing process as it’s manufactured with non-corrosive KAIF4/CSKAIF4 Flux injection technology patented and registered as complete seamless in the wires or rings. It does not require cleaning or little cleaning is needed post brazing as it is made with non-corrosive flux. Controlled flux ratio percentage to ensure that the flux is consistent across the wire for repeated high performance flow of the alloy.
₹425.00 (excl. GST) -
Aluminum Electrolytic Capacitor Assorted Kit – 12 Kinds 0.22-F-470-F
Features:
1.Made of high-quality material, durable, and practical to use.
2.Durable and easy to install.
3.Very convenient and practical.
4.Very popular with electronics enthusiasts.
5.A variety of types of electrolytic capacitors to meet your different needs.₹200.00 (excl. GST)Aluminum Electrolytic Capacitor Assorted Kit – 12 Kinds 0.22-F-470-F
₹200.00 (excl. GST) -
Aluminum Flexible Coupling Coupler Helical Shaft 5mm x 8mm
Features :
- Corrosion resistance and High Durability
- One piece construction with long-lasting performance
- Torsional stiffness: Zero backlash
- Low moment of inertia offering constant velocity
₹110.00 (excl. GST)Aluminum Flexible Coupling Coupler Helical Shaft 5mm x 8mm
₹110.00 (excl. GST) -
Aluminum Flexible Shaft Coupling 5mm x 5mm
Features :
- Corrosion resistance and High Durability
- One piece construction with long-lasting performance
- Torsional stiffness: Zero backlash
- Low moment of inertia offering constant velocity
₹120.00 (excl. GST)Aluminum Flexible Shaft Coupling 5mm x 5mm
₹120.00 (excl. GST) -
Aluminum GT2 16 Tooth Timing Pulley 5mm Bore For 6mm Belt – 2Pcs
FEATURES-
- Material: Aluminum.
- No. of teeth: 16.
- Outer Diameter: 13mm.
- Inner Diameter: 5mm.
- Length: 14 mm.
- Weight: 6 gm.
₹110.00 (excl. GST)Aluminum GT2 16 Tooth Timing Pulley 5mm Bore For 6mm Belt – 2Pcs
₹110.00 (excl. GST) -
Aluminum GT2 20 Tooth Timing Pulley 6.35mm Bore For 6mm Belt
FEATURES-
- Material: Aluminum.
- No. of teeth: 20.
- Outer Diameter: 16mm.
- Inner Diameter: 6.35mm.
- Length: 14 mm.
- Weight: 6 gm.
₹125.00 (excl. GST)Aluminum GT2 20 Tooth Timing Pulley 6.35mm Bore For 6mm Belt
₹125.00 (excl. GST) -
Aluminum GT2 Timing Pulley 36 Tooth 8mm Bore For 6mm Belt
- Outer Diameter: 25.5 mm.
- Inner Diameter: 8 mm.
- Width: 17 mm.
- Weight: 14 gm.
- Material: Aluminum.
- No. of teeth: 36 on each side
₹105.00 (excl. GST)Aluminum GT2 Timing Pulley 36 Tooth 8mm Bore For 6mm Belt
₹105.00 (excl. GST) -
Aluminum GT2 Timing Pulley 40 Tooth 5mm Bore For 6mm Belt
This pulley has 40Â teeth and a 5mm inner bore. Two set screws can be used to attach it firmly to any 5mm diameter shaft. Full aluminum construction means these are very light and very durable.
Specifications-
- Material: Aluminum.
- No. of teeth: 40.
- Outer Diameter: 27 mm.
- Inner Bore Diameter: 5mm.
₹156.00 (excl. GST)Aluminum GT2 Timing Pulley 40 Tooth 5mm Bore For 6mm Belt
₹156.00 (excl. GST) -
Anti-Corrosion Water Level Sensor with Ball Float Switch
- Rating contract (Max.): 10 W
- Switching power supply (Max.): 110VDC
- Resistance contract (Max.): 100 Ω
- Appro. Float Ball Size (mm) : 24×17 (LxD)
- Body Total Length (mm) : 85
- Cable Length (cm) : 37
- Total Float opening: 70°
- Switch ON/OFF angle Approx. betn 15° to 20°
₹87.00 (excl. GST)Anti-Corrosion Water Level Sensor with Ball Float Switch
₹87.00 (excl. GST) -
Anti-Vibration Shock Absorber for APM/KK/MWC/PixHawk
Features:
- Easy to use
- Easily Replaceable
₹140.00 (excl. GST)Anti-Vibration Shock Absorber for APM/KK/MWC/PixHawk
₹140.00 (excl. GST) -
Anycubic I3 MEGA S – FDM 3D Printer
Features:
Printing Platform: Strong adhesive when platform’s hot and easy to remove when cool down.
Filament Sensor: Provides better printing experience of flexible
Fast Assembly: Only need to install 8 screws and connect 3 wires before the first print.
Rigid Metal Frame: The structure is very stable which could reduce the body shake druing printing and improve the printing quality
Suspended Filament Rack: One-piece hanging design, simple and beautiful. The feeding of filament is smoother and the storage of filament is more convenint.₹14,500.00 (excl. GST)Anycubic I3 MEGA S – FDM 3D Printer
₹14,500.00 (excl. GST)
