-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
Features :
- Microstep resolutions:Â full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Adjustable current control lets you set the maximum current output with a potentiometer. Hence lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- 45Â V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
- Can interface directly with 3.3Â V and 5Â V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- 4-layer, 2Â oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
₹126.00 (excl. GST)DRV8825 Stepper Motor Driver with Aluminum Heat Sink
₹126.00 (excl. GST) -
Optical Liquid Level Sensor
Features:Â
- Measuring accuracy: 1MM
- Current output :15mA
- Operating voltage: 5v
- No mechanical moving parts, high reliability
- High precision level control
- Meet the safety standard requirements
- An easily mounting method with locking nut.
- Measurement range: single-point measurements
- Equipped with 50 cm cable length.
₹710.00 (excl. GST)Optical Liquid Level Sensor
₹710.00 (excl. GST) -
eSun PLA+ 1.75mm 3D Printing Filament 1kg-White
Features:
- Consistently High Quality
- Made from great, high-performance materials
- Ready to print on any open source desktop or industrial printer
- Deliver exceptional performance
- 100% bio-degradable and FDA food safety approved
- 10 times stronger than regular PLA on the market
- No wire-drawing problems, the surface of the printouts will be smoother and more delicate
- No cracking problem and brittle issue
- Low material shrinkage rate, uniform diameter
Printing Settings:
- Best Printing Temperature：200-220℃
- Bed Temperature：0-70℃
- Printing Speed：30~90mm/s
- Movement Speed ：90~150mm/s
Maintenance tips:
- Please put the unprinted material in sealed bags, then place it in a cool and dry place to prevent moisture.
- Please insert the wire into the fixed hole of the tray when you don’t use it in case of knotting.
- ABS will produce a slight irritating smell, please print in a well-ventilated environment.
₹1,090.00 (excl. GST)eSun PLA+ 1.75mm 3D Printing Filament 1kg-White
₹1,090.00 (excl. GST) -
eSun PLA+ 1.75mm 3D Printing Filament 1kg-Red
Features:
- Consistently High Quality
- Made from great, high-performance materials
- Ready to print on any open source desktop or industrial printer
- Deliver exceptional performance
- 100% bio-degradable and FDA food safety approved
- 10 times stronger than regular PLA on the market
- No wire-drawing problems, the surface of the printouts will be smoother and more delicate
- No cracking problem and brittle issue
- Low material shrinkage rate, uniform diameter
Printing Settings:
- Best Printing Temperature：200-220℃
- Bed Temperature：0-70℃
- Printing Speed：30~90mm/s
- Movement Speed ：90~150mm/s
Maintenance tips:
- Please put the unprinted material in sealed bags, then place it in a cool and dry place to prevent moisture.
- Please insert the wire into the fixed hole of the tray when you don’t use it in case of knotting.
- ABS will produce a slight irritating smell, please print in a well-ventilated environment.
₹1,090.00 (excl. GST)eSun PLA+ 1.75mm 3D Printing Filament 1kg-Red
₹1,090.00 (excl. GST) -
10mm LDR Sensor Photoresistor Photo Cell 50-100k – GL10539
Feature:
- Epoxy encapsulation
- Good reliability
- Small size
- High sensitivity
- Fast response
- Good spectral characteristics
₹33.00 (excl. GST)10mm LDR Sensor Photoresistor Photo Cell 50-100k – GL10539
₹33.00 (excl. GST) -
WeMos d1 Mini- IOT ESP8266 Based Development Board
- Specification and Features :-
- 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Use BRT (Bias Resistor Transistor), easier into flash mode.
- 30% increase in radiating area, more stable.
- Dimensions : 35 x 26 x 8 (LxWxH) mm.
- Weight: 10 gm.
- Board Color : Blue
- Compatible with Arduino
- Compatible with NodeMCU
- Compatible with MicroPython
₹200.00 (excl. GST)WeMos d1 Mini- IOT ESP8266 Based Development Board
₹200.00 (excl. GST) - Specification and Features :-
-
70 x 20mm Pulley Wheel with 6mm Shaft Hole Diameter
Features :
- Smooth surface
- Durable
- Lightweight
₹20.00 (excl. GST)70 x 20mm Pulley Wheel with 6mm Shaft Hole Diameter
₹20.00 (excl. GST) -
70 x 40 mm Pulley Wheel with 6mm Shaft Hole Diameter
Features :
- Smooth surface
- Durable
- Lightweight
₹35.00 (excl. GST)70 x 40 mm Pulley Wheel with 6mm Shaft Hole Diameter
₹35.00 (excl. GST) -
₹50.00 (excl. GST)8 Channel Bi-Directional Logic Level Converter Module
₹50.00 (excl. GST) -
HM-10 BLE Bluetooth 4.0 CC2541 Wireless Module
Features :
- It’s easy to use and completely encapsulated.
- You can set it as a slave or master.
- You can use the AT command set the baud rate.
- Coverage up to 60 meters.
- Built-in PCB antenna.
- UART design.
- Support bridge direct-driven mode simultaneously (no need for extra CPU).
- 20ms connection interval (default), quick to connect; Support AT instruction, to modify the baud rate of the serial port, gain MAC address and modify module name.
- Support AT instruction, to adjust the Bluetooth connection interval and control the forwarding rate (dynamic power consumption adjustment).
- Support APP; IO expansion.
- 2 channel ADC input (14 bit).
- 4 channel PWM (120Hz) output.
- The RSSI successive acquisition, auto read, and notification to APP (used in anti-lost alarm).
- Power indicator/alert.
- Support anti-hijack password setup, modification, and restoration.
- Ultra-low power consumption standby mode.
₹375.00 (excl. GST)HM-10 BLE Bluetooth 4.0 CC2541 Wireless Module
₹375.00 (excl. GST) -
LM358DR SOIC-8 High Gain Operational Amplifier
Features:
- Single supply voltage from 3V to 32V and dual supply range from ±1.5V to ±16V
- Slew rate at unity gain is 0.3 V/µs
- Wide unity gain bandwidth of 0.7MHz
- Low drain supply current is 0.7mA independent of supply voltage
- Input offset voltage of 3mV
- Input offset current of 2nA
- Input bias current of -20nA
- Differential input voltage range equal to the maximum rated supply voltage of 32V
- Common mode rejection ratio (CMRR) of 80dB
- Operating temperature range from 0°C to 70°C
- Applications: Signal Processing, Sensing & Instrumentation, Consumer Electronics, Portable Devices, Motor Drive & Control
₹39.00 (excl. GST)LM358DR SOIC-8 High Gain Operational Amplifier
₹39.00 (excl. GST) -
PCB Drill bit
Drill bit Applications:
- Drilling PCBs
- Drilling ornaments
- Drilling thin Aluminium plates
Drill bit specification:
- 0.8mm diameter
- High quality stainless steel
- Long term durability
- Good for though surfaces
₹12.00 (excl. GST)PCB Drill bit
₹12.00 (excl. GST)