-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
Digital LDR Module Sensor Wholesale/B2B (Pack of 25)
Features :
- LM393 based design.
- It can detect ambient brightness and light intensity.
- Adjustable sensitivity (via blue digital potentiometer adjustment).
- Output Digital – 0V to 5V, Adjustable trigger level from preset.
- LEDs indicating output and power.
₹525.00 (excl. GST)Digital LDR Module Sensor Wholesale/B2B (Pack of 25)
₹525.00 (excl. GST) -
Digital LDR Sensor Module for Light Detection Sensing
Features :
- LM393 based design.
- It can detect ambient brightness and light intensity.
- Adjustable sensitivity (via blue digital potentiometer adjustment).
- Output Digital – 0V to 5V, Adjustable trigger level from preset.
- LEDs indicating output and power.
₹22.00 (excl. GST)Digital LDR Sensor Module for Light Detection Sensing
₹22.00 (excl. GST) -
Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹750.00 (excl. GST)Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
₹750.00 (excl. GST) -
Rain Drop Detection Sensor Module Wholesale/B2B (Pack of 25)
Features:
Operating voltage: 5V
Provide both digital and analog output
Adjustable sensitivity
Output LED indicator
Compatible with Arduino, Raspberry and other projects
TTL Compatible
Bolt holes for easy installation₹650.00 (excl. GST)Rain Drop Detection Sensor Module Wholesale/B2B (Pack of 25)
₹650.00 (excl. GST) -
Right Side MK8 extruder Aluminum 3D Printer Block
 Specifications and Features:
- Right Short Side MK8 Extruder
- High-Quality Replacement for your blocked/damaged MK8 Extruder
- Available in 3 different types to support dual extruder setup
- Material: Aluminum alloy
- Weight: 60gm
₹169.00 (excl. GST)Right Side MK8 extruder Aluminum 3D Printer Block
₹169.00 (excl. GST) -
XBee Shield V03 Module Wireless Control
Applications :
- PC via a USB cable directly connected with XBee adapters.
- Bluetooth Bee configures or uses as a data-transmission.
- Arduino board pro mini downloader.
Features :
- Stackable design, easy to plug into the ARDUINO development board.
- Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly.
- Coupled with the XBee module, you can achieve two or more sets of communication between Arduino or Arduino and PC Communications.
- 3.3v and 5v dual power output.
- 3.3v and 5v IO compatible.
- USB 2.0 protocol.
- Bitbang mode ready.
- Easily connected to a PC via mini USB Cable.
- XBee-setting support software X-CTU.
₹126.00 (excl. GST)XBee Shield V03 Module Wireless Control
₹126.00 (excl. GST) -
Arduino LilyPad ATmega328P compatible Board
Features :
- Board will run from 2V to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
- The backside of the LilyPad is now completely flat!
- We now use a surface mount programming connector to keep the header from poking through.
- This version of the LilyPad now uses the new ATmega328 at 8MHz.
- Arduino 0016 supports the Pro Mini Arduino 328/8MHz/16MHZ.
- Use this setting when using this new LilyPad 328.
₹500.00 (excl. GST)Arduino LilyPad ATmega328P compatible Board
₹500.00 (excl. GST) -
Cytron 20Amp 6V-30V DC Motor Driver (2 Channels)
Features:
- Bidirectional control for two brushed DC motors.
- Operating Voltage: DC 6V to 30V.
- Maximum Motor Current (Each Channel): 20A continuous, 60A peak.
- Buttons for quick testing.
- LEDs for motors output state.
- Temperature protection.
- Undervoltage shutdown.
Example Application:Â Automated Guided Vehicle (AGV), Solar Tracker, Game Simulator, Mobile Robot, Automation Machine.
₹2,660.00 (excl. GST)Cytron 20Amp 6V-30V DC Motor Driver (2 Channels)
₹2,660.00 (excl. GST) -
UNO SMD Atmega328P Development Board compatible with Arduino
Features-
- Flash Memory – 32 KB (ATmega32u4) of which 4 KB used by boot loader
- SRAM – 2 KB (ATmega328P)
- EEPROM – 1 KB (ATmega328P)
₹190.00₹550.00(excl. GST)UNO SMD Atmega328P Development Board compatible with Arduino
₹190.00₹550.00(excl. GST) -
5-60V SSR-10 DD Solid State Relay
Features:
- Long service life and high reliability
- Reduced electromagnetic interference
- Highly reliable, compact size designed to offer users maximum simplicity
₹610.00 (excl. GST)5-60V SSR-10 DD Solid State Relay
₹610.00 (excl. GST) -
1uF (1000nF) 50V Capacitor 1206 SMD Package – (pack of 5)
Features:
- Supplied in tape on reel
- Nickel-barrier end termination
- RoHS compliant
- Halogen Free compliant
₹5.00 (excl. GST)1uF (1000nF) 50V Capacitor 1206 SMD Package – (pack of 5)
₹5.00 (excl. GST) -
220pF 1206 Surface Mount Multilayer Ceramic Capacitor– (pack of 5)
Features:
- Supplied in tape on reel
- Nickel-barrier end termination
- RoHS compliant
- Halogen Free compliant
₹5.00 (excl. GST)220pF 1206 Surface Mount Multilayer Ceramic Capacitor– (pack of 5)
₹5.00 (excl. GST)
