-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
- “Creality Ender 5 Plus 3D Printer” already exists in your wishlist
-
Automatic Sanitizer Dispenser/Tunnel Control Board with inbuilt IR (InfraRed) Sensor Interface, Relay, Timer Control and Motor Port Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹175.00 (excl. GST) -
₹180.00 (excl. GST)Avr Usb Programmer Usbasp Usbisp Isp For Atmel Atmega Attiny Microcontrollers
₹180.00 (excl. GST) -
BASIC NX3224T028 2.8″HMI LCD Touch Display
Features:
- 320 x 240 Resolution
- RGB 65K true to life colours
- TFT screen with integrated resistive touch panel
- 4 pin TTL serial interface
- 4M Flash memory for User Application Code and Data
- Onboard micro-SD card slot for firmware upgradation
- Visual Area: 57.6mm(L)×43.2mm(W)
- Adjustable Brightness: 0~180 nit, the interval of adjustment is 1%
- 5V65mA power consumption
- Compatible with Raspberry Pi A+, B+, Pi 2, Pi 3, Arduino.
- Certificates: CE/EMC, RoHS (certificates)
Software:
₹2,450.00 (excl. GST)BASIC NX3224T028 2.8″HMI LCD Touch Display
₹2,450.00 (excl. GST) -
Basic Robotics kit
Basic Robotics kit
ï‚·Â Breadboard – 1
ï‚·Â DC Motor – 1
ï‚·Â Buzzer – 1
ï‚·Â Green LED – 1
ï‚·Â Red LEDs – 2
ï‚·Â Push Button Switches – 3
ï‚·Â Slide Switch – 1
ï‚·Â Red Alligator Clip – 1
ï‚·Â Black Alligator Clip – 1
ï‚·Â Connecting Towers – 6
ï‚·Â 10kΩ Resistor – 1
ï‚·Â 20kΩ Resistor – 1
ï‚·Â 3.3kΩ Resistor – 1
ï‚·Â Capacitor – 1
 Jumper Wires – 3
₹10,170.00 (excl. GST)Basic Robotics kit
₹10,170.00 (excl. GST) -
BMP 280 Barometric Pressure and Altitude Sensor I2C/SPI Module
- Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V
- Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C)
- Operating Pressure: 300 hPa to 1100 hPa
- Peak current: 1.12mA
- Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m
₹40.00 (excl. GST)BMP 280 Barometric Pressure and Altitude Sensor I2C/SPI Module
₹40.00 (excl. GST) -
BMP180 Barometric Pressure Altitude Sensor I2C/SPI Module
Specifications and Features :
- Get more precise temperature, atmospheric pressure values, and approximate altitude data
- Enhancement of GPS navigation (e.g. time-to first-fix improvement, dead-reckoning, slope detection)
- Indoor navigation (floor detection, elevator detection)
- Outdoor navigation, leisure and sports applications
- Weather forecast
- Health care applications (e.g. spirometry)
- Vertical velocity indication (e.g. rise/sink speed)
- Libraries and tutorials available for Arduino and other microcontrollers
- Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V
- Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C)
- Peak current: 1.12mA
- Operating Pressure: 300 hPa to 1100 hPa
- Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m
₹32.00 (excl. GST)BMP180 Barometric Pressure Altitude Sensor I2C/SPI Module
₹32.00 (excl. GST) -
Bms 13S 40A 48V Waterproof Protection Circuit Module
- 13S 48V BMS
- Discharging current – 40A
- Charging current – 20 A
- Waterproof.
₹1,250.00 (excl. GST)Bms 13S 40A 48V Waterproof Protection Circuit Module
₹1,250.00 (excl. GST) -
BMS 15S 48V 40A DALY LiFePo4 Waterproof Battery Management System
BMS 15S 48V 40A
Specification:-
- Balance Current (mA): 30±5
- Balance Detect Voltage (V): 3.5
- Cable Size (AWG): 10
- Charge Current (A):Â 20
- Charge Voltage (V): 54.75
- Height (mm):Â 10.6
- Length (mm): 81.5
- Model: 15S 48V 40A
- Over Discharge Detect (V): 2.2±0.05
- Over Discharge Release (V): Off load
- Overcharge Detect Voltage (V): 3.75±0.05
- Overcharge Release Voltage (V): 3.55±0.05
- Width (mm): 60.6
- Working Current (uA): 100
- Working Temperature Range (°C): -20 to 70
₹1,800.00 (excl. GST)BMS 15S 48V 40A DALY LiFePo4 Waterproof Battery Management System
₹1,800.00 (excl. GST) -
BMS 24V 7S 20A Daly Waterproof BMS for Li-ion Cell (NMC) 25.9V
Features :
- Strong load ability, constant discharge current 10A~250A , use high voltage resistance, low inner resistance power Mosfet. The heat sink will greatly help cooling.
- IC itself has power balancing function. The circuit is simple and reliable.
- Typical voltage detection for each cell. So each battery will be prevented over charged or over discharged. Over current and short circuit protection function is very reliable. long time short circuit of the load won’t affect the PCB and the battery. Temperature protection during charging and discharging.
- Extreme low power consumption. the consumption of the whole device is less than 50uA.
- PCB use high anti-corrosion, high water resistance, high impedance ESD conformal coating.
₹850.00 (excl. GST)BMS 24V 7S 20A Daly Waterproof BMS for Li-ion Cell (NMC) 25.9V
₹850.00 (excl. GST) -
BMS 4 Series 14.8V 18650 Lithium Battery Equalization Board
- Type:Â Voltage Regulator
- Supply Voltage:14.8V/16.8V
- Dissipation Power:18650 Lithium Battery Balanced Function Board
- Operating Temperature:Â Discharge Shunt balanced 4.2V 66mA
₹79.00 (excl. GST)BMS 4 Series 14.8V 18650 Lithium Battery Equalization Board
₹79.00 (excl. GST) -
BMS 4S 12V 60A Daly Lifepo4 -Battery Management System
- Brand: Daly
- Model: 4S 12V 60A
- Charge Current: 30A
- Discharge Current: 60A
- Battery Type: Lithium-Ion Battery
- Input Voltage (V): 12V
- Number of cells in series: 4S
₹1,395.00 (excl. GST)BMS 4S 12V 60A Daly Lifepo4 -Battery Management System
₹1,395.00 (excl. GST) -
BMS 8S 24V 20A DALY Lifepo4 Battery Management System
- Model: 8S 24V 20A
- Battery Type: Lithium Battery
- No.of cells in series: 8s
- Discharge Current: 20A
- Charge Current: 10A
₹800.00 (excl. GST)BMS 8S 24V 20A DALY Lifepo4 Battery Management System
₹800.00 (excl. GST)
