-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹638.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹638.00(Price is Exclusive of GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹264.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹264.00 (Price is Exclusive of GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST) -
ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (Price is Exclusive of GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (Price is Exclusive of GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹207.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹207.00 (Price is Exclusive of GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)
-
Aluminum Flexible Coupling Coupler Helical Shaft 5mm x 8mm
Features :
- Corrosion resistance and High Durability
- One piece construction with long-lasting performance
- Torsional stiffness: Zero backlash
- Low moment of inertia offering constant velocity
₹110.00 (Price is Exclusive of GST)Aluminum Flexible Coupling Coupler Helical Shaft 5mm x 8mm
₹110.00 (Price is Exclusive of GST) -
Aluminum Flexible Shaft Coupling 5mm x 5mm
Features :
- Corrosion resistance and High Durability
- One piece construction with long-lasting performance
- Torsional stiffness: Zero backlash
- Low moment of inertia offering constant velocity
₹120.00 (Price is Exclusive of GST)Aluminum Flexible Shaft Coupling 5mm x 5mm
₹120.00 (Price is Exclusive of GST) -
Aluminum GT2 16 Tooth Timing Pulley 5mm Bore For 6mm Belt – 2Pcs
FEATURES-
- Material: Aluminum.
- No. of teeth: 16.
- Outer Diameter: 13mm.
- Inner Diameter: 5mm.
- Length: 14 mm.
- Weight: 6 gm.
₹110.00 (Price is Exclusive of GST)Aluminum GT2 16 Tooth Timing Pulley 5mm Bore For 6mm Belt – 2Pcs
₹110.00 (Price is Exclusive of GST) -
Aluminum GT2 20 Tooth Timing Pulley 6.35mm Bore For 6mm Belt
FEATURES-
- Material: Aluminum.
- No. of teeth: 20.
- Outer Diameter: 16mm.
- Inner Diameter: 6.35mm.
- Length: 14 mm.
- Weight: 6 gm.
₹80.00 (Price is Exclusive of GST)Aluminum GT2 20 Tooth Timing Pulley 6.35mm Bore For 6mm Belt
₹80.00 (Price is Exclusive of GST) -
Aluminum GT2 Timing Pulley 36 Tooth 8mm Bore For 6mm Belt
- Outer Diameter: 25.5 mm.
- Inner Diameter: 8 mm.
- Width: 17 mm.
- Weight: 14 gm.
- Material: Aluminum.
- No. of teeth: 36 on each side
₹105.00 (Price is Exclusive of GST)Aluminum GT2 Timing Pulley 36 Tooth 8mm Bore For 6mm Belt
₹105.00 (Price is Exclusive of GST) -
Aluminum GT2 Timing Pulley 40 Tooth 5mm Bore For 6mm Belt
This pulley has 40Â teeth and a 5mm inner bore. Two set screws can be used to attach it firmly to any 5mm diameter shaft. Full aluminum construction means these are very light and very durable.
Specifications-
- Material: Aluminum.
- No. of teeth: 40.
- Outer Diameter: 27 mm.
- Inner Bore Diameter: 5mm.
₹156.00 (Price is Exclusive of GST)Aluminum GT2 Timing Pulley 40 Tooth 5mm Bore For 6mm Belt
₹156.00 (Price is Exclusive of GST) -
AMS NMC 21700 5000mAh (3c) Lithium-Ion Battery
- Product: Lithium-Ion Cell
- Model: AMS NMC 21700
- Battery cell type: (3C)
- Watt-hours: 18Wh
- Nominal voltage: 3.70 V
- Charge voltage: 4.20 V
₹739.00 (Price is Exclusive of GST)AMS NMC 21700 5000mAh (3c) Lithium-Ion Battery
₹739.00 (Price is Exclusive of GST) -
AMS1117-3.3V, 1A, SOT-223 Voltage Regulator IC
- Low dropout voltage
- Load regulation: 0.2% typical
- Optimized for Low Voltage
- On-chip thermal limiting
- Built-in thermal shutdown
- Good noise rejection
₹9.00 (Price is Exclusive of GST)AMS1117-3.3V, 1A, SOT-223 Voltage Regulator IC
₹9.00 (Price is Exclusive of GST) -
AMS1117-5.0V, 1A, SOT-223 Voltage Regulator IC
- Low dropout voltage
- Load regulation: 0.2% typical
- Optimized for Low Voltage
- On-chip thermal limiting
- Built-in thermal shutdown
- Good noise rejection
₹10.00 (Price is Exclusive of GST)AMS1117-5.0V, 1A, SOT-223 Voltage Regulator IC
₹10.00 (Price is Exclusive of GST) -
Anti-Corrosion Water Level Sensor with Ball Float Switch
- Rating contract (Max.): 10 W
- Switching power supply (Max.): 110VDC
- Resistance contract (Max.): 100 Ω
- Appro. Float Ball Size (mm) : 24×17 (LxD)
- Body Total Length (mm) : 85
- Cable Length (cm) : 37
- Total Float opening: 70°
- Switch ON/OFF angle Approx. betn 15° to 20°
₹92.00 (Price is Exclusive of GST)Anti-Corrosion Water Level Sensor with Ball Float Switch
₹92.00 (Price is Exclusive of GST) -
Anti-Vibration Shock Absorber for APM/KK/MWC/PixHawk
Features:
- Easy to use
- Easily Replaceable
₹125.00 (Price is Exclusive of GST)Anti-Vibration Shock Absorber for APM/KK/MWC/PixHawk
₹125.00 (Price is Exclusive of GST) -
Anycubic I3 MEGA S – FDM 3D Printer
Features:
Printing Platform: Strong adhesive when platform’s hot and easy to remove when cool down.
Filament Sensor: Provides better printing experience of flexible
Fast Assembly: Only need to install 8 screws and connect 3 wires before the first print.
Rigid Metal Frame: The structure is very stable which could reduce the body shake druing printing and improve the printing quality
Suspended Filament Rack: One-piece hanging design, simple and beautiful. The feeding of filament is smoother and the storage of filament is more convenint.₹14,500.00 (Price is Exclusive of GST)Anycubic I3 MEGA S – FDM 3D Printer
₹14,500.00 (Price is Exclusive of GST)
