No products in the cart.
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (Price is Exclusive of GST)
Castor wheel with steel ball
- Dimensions: 22 x 15 mm (Diameter x Height)
- Weight: 10 gm
- Body Case Material: Plastic
- Ball Material: 304 Stainless Steel
- Application: for MiniQ robot
₹20.00 (Price is Exclusive of GST)Castor wheel with steel ball
₹20.00 (Price is Exclusive of GST)- ₹160.00 (Price is Exclusive of GST)
Ceramic Capacitor Kit -300pcs (30 Kinds )
₹160.00 (Price is Exclusive of GST) Ceramic Capacitor Kit 250pcs 25 value 1PF-0.1UF
- Good Quality item
- 25 values with 10pcs for each value
₹110.00 (Price is Exclusive of GST)Ceramic Capacitor Kit 250pcs 25 value 1PF-0.1UF
₹110.00 (Price is Exclusive of GST)Ceramic Capacitor-220pF 1206 (Surface Mount Multilayer )- (Pack of 30)
Ceramic Capacitor-220pF 1206
- Capacitance: 220 pF
- Voltage: 50V
- Mounting type: SMD/SMT
- Operating temperature: -55ºC to 125ºC
- Supplied in tape on reel
- Nickel-barrier end termination
- RoHS compliant
- Halogen Free compliant
₹29.00 (Price is Exclusive of GST)Ceramic Capacitor-220pF 1206 (Surface Mount Multilayer )- (Pack of 30)
₹29.00 (Price is Exclusive of GST)Ceramic Cement Power Resistors 5W Watt 10K Ohm 5% (Pack of 5)
- Product Name : Cement Resistor;
- Body Material : Ceramic, Cement
- Power : 5W;Resistance : 10KÎ
- Tolerance : ±5% (J);
- Body Size (Approx.) : 22 x 9 x 10mm/0.86″ x 0.35″ x 0.39″ (L * W * H)
- Lead Diameter (Approx.) : 0.8mm / 0.031″;Color : White
₹30.00 (Price is Exclusive of GST)Ceramic Cement Power Resistors 5W Watt 10K Ohm 5% (Pack of 5)
₹30.00 (Price is Exclusive of GST)CHAM CMINR14500F2 3.6V 850mAh 2C AA Size Li-ion Battery
- Nominal Voltage: 3.6 V
- Battery Capacity: 850 mAh
- Life Cycle: 800 Times(Approximately)
- Maximum Charge Voltage: 4.2 V (±0.05)
- Rechargeable: Yes
₹263.00 (Price is Exclusive of GST)CHAM CMINR14500F2 3.6V 850mAh 2C AA Size Li-ion Battery
₹263.00 (Price is Exclusive of GST)Charger Board Protection Module for Lithium Battery 3S 10A 12V 18650
Charger Board Protection
Features :
- Operating current : 6 – 8A.
- Current limit : 10 – 13A.
- Storage condition : -40 ~ +80 ℃.
- Resting current: less than 30uA.
- Effective lifetime: over 30,000 hours.
- Internal resistance: less than 100mΩ.
- Short-circuit protection: protection.
- Self-recovery delay.
₹46.00 (Price is Exclusive of GST)Charger Board Protection Module for Lithium Battery 3S 10A 12V 18650
₹46.00 (Price is Exclusive of GST)CN3791 12V MPPT Solar Charger Module
CN3791 12V MPPT Solar Charger Module
Features:
- Maximum Power Point Tracking (MPPT) Solar Charger Module
- 2-Pin JST Connectors for Solar Panel and Battery Connection
- PWM Switching Frequency of 300KHz
- Maximum Charging Current of 2A
₹195.00 (Price is Exclusive of GST)CN3791 12V MPPT Solar Charger Module
₹195.00 (Price is Exclusive of GST)CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
Features :
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
₹116.00 (Price is Exclusive of GST)CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
₹116.00 (Price is Exclusive of GST)Color sensor recognition module
- Operating Voltage: 3V-5V
- High-resolution conversion of light intensity to frequency.
- Chip pins all has drawn for standard 100.
- Put the needle (2.54 mm).
- Mil-convenient for bitmap board.
- Programmable color and full-scale output frequency.
- Communicate directly with a microcontroller.
- Low-profile surface mount package.
₹260.00 (Price is Exclusive of GST)Color sensor recognition module
₹260.00 (Price is Exclusive of GST)Combination Screwdriver Set (Pack of 31) – JK 6036
Meet the Jackly 31-in-1 ratchet screwdriver set – the tool that every household should have. With this compact screwdriver set, you can complete all the pending repair works by opening mobile phones, computers, PDA housings, PSPs, NDS, and music players.
₹145.00 (Price is Exclusive of GST)Combination Screwdriver Set (Pack of 31) – JK 6036
₹145.00 (Price is Exclusive of GST)Component/IC Extraction Tool
IC Extraction Tool
- Dimensions : 97 x 45 x 14 mm
- Weight: 21 grams
- The PLCC can be easily removed from the substrate without damaging any IC conductors.
- Fits: The chip extraction tool is perfectly suitable for motherboards, microcontrollers, and programmers.
- Can be used to remove PLCC and IC from Sockets
- Made up of High-Quality Steel for durability
- Plastic Shielding to Prevent Shocks
₹170.00 (Price is Exclusive of GST)Component/IC Extraction Tool
₹170.00 (Price is Exclusive of GST)
