-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹638.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹638.00(Price is Exclusive of GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹264.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹264.00 (Price is Exclusive of GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST) -
ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (Price is Exclusive of GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (Price is Exclusive of GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹207.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹207.00 (Price is Exclusive of GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)
-
BMS 24V 7S 20A Daly Waterproof BMS for Li-ion Cell (NMC) 25.9V
Features :
- Strong load ability, constant discharge current 10A~250A , use high voltage resistance, low inner resistance power Mosfet. The heat sink will greatly help cooling.
- IC itself has power balancing function. The circuit is simple and reliable.
- Typical voltage detection for each cell. So each battery will be prevented over charged or over discharged. Over current and short circuit protection function is very reliable. long time short circuit of the load won’t affect the PCB and the battery. Temperature protection during charging and discharging.
- Extreme low power consumption. the consumption of the whole device is less than 50uA.
- PCB use high anti-corrosion, high water resistance, high impedance ESD conformal coating.
₹850.00 (Price is Exclusive of GST)BMS 24V 7S 20A Daly Waterproof BMS for Li-ion Cell (NMC) 25.9V
₹850.00 (Price is Exclusive of GST) -
Mini Sewing Machine – JYSM-202A
-Mini sewing machine offers double threads and perfect control of points
-Best view and more convenient in cutting the thread
-Small size, lightweight and with exquisite finish
-Equipped with a light lamp and a wire cutter, easy to cut the wires
-A large coil can be used with a rewind device for easy replacement of the bottom bobbin₹850.00₹950.00(Price is Exclusive of GST)Mini Sewing Machine – JYSM-202A
₹850.00₹950.00(Price is Exclusive of GST) -
3D Printer Filament – Multicolor PLA 1.75MM
- It is fed into the FDM 3D printer.
- It is extruded and deposited by an extrusion head onto a build platform where it cools.
- The process is continuous, building up layers to create the model.
₹850.00 (Price is Exclusive of GST)3D Printer Filament – Multicolor PLA 1.75MM
₹850.00 (Price is Exclusive of GST) -
Official Raspberry Pi M.2 HAT+
- Fast Data Transfer:Â Achieve speeds of up to 450 Mbytes/s with the 4 Gbits/s PCIe 2.0 interface for NVMe SSDs and PCIe accessories.
- Seamless Compatibility:Â Fully compliant with HAT+ specification for easy integration with Raspberry Pi 5.
- Plug-and-Play:Â Automatically detected by the latest Raspberry Pi software and firmware.
- Easy Installation:Â Comes with a 16mm stacking header, spacers, and screws for convenient setup with the Active Cooler in place.
₹848.00 (Price is Exclusive of GST)Official Raspberry Pi M.2 HAT+
₹848.00 (Price is Exclusive of GST) -
SeeedStudio Grove GSR sensor
SeeedStudio
Features:
- Detects conductance of the skin
- Finger Straps for electrodes
₹840.00 (Price is Exclusive of GST)SeeedStudio Grove GSR sensor
₹840.00 (Price is Exclusive of GST) -
Pro-Range INR 18650 11.1V 2000mAh 3C 3S1P Li-Ion Battery Pack with DC Jack Male & Female
- Nominal Capacity (mAh): 2000
- Nominal Voltage (v): 11.1
- Max Charging Voltage (v): 12.6
- Charge Port: DC Female
- Discharge Port: DC Male
₹838.00 (Price is Exclusive of GST)Pro-Range INR 18650 11.1V 2000mAh 3C 3S1P Li-Ion Battery Pack with DC Jack Male & Female
₹838.00 (Price is Exclusive of GST) -
Three-terminal Regulator Tube Sorting Box Kit
Three-terminal Regulator Tube Box Kit
5pcs 17805
5pcs 17806
5pcs 17808
5PC 17809
5pcs 17810
5pcs 17812
5pcs 17815
5pcs 17818
5pcs 17824
5pcs Im317₹838.00 (Price is Exclusive of GST)Three-terminal Regulator Tube Sorting Box Kit
₹838.00 (Price is Exclusive of GST) -
SMPS Adaptor of 24V 2.5Amps
- Material: Plastic
- Colour: Black
- Dimensions (L x B x H): 6.5 cm x 3.5 cm x 10 cm
- Weight: 120 g
- Package Contents: 1 RO Water Purifier SMPS
- Warranty: 6 Months Seller Warranty on Manufacturing Defects
- Care Instructions: Check specifications before use
₹837.00 (Price is Exclusive of GST)SMPS Adaptor of 24V 2.5Amps
₹837.00 (Price is Exclusive of GST) -
12V 3.5A 4000ml/min Liquid Diaphragm Pump
Features:
- Self-Priming
- Low Power Consumption
- Long Life
- Can Run in Dry Condition
₹835.00 (Price is Exclusive of GST)12V 3.5A 4000ml/min Liquid Diaphragm Pump
₹835.00 (Price is Exclusive of GST) -
Pro-Range 3.7V 2200mAh 25C 1S Lithium Polymer Battery Pack
- Model No: Pro-Range 2200/1S-25C
- Product Type: Lithium Polymer Battery Pack
- The Pro-Range LiPo battery has matched resistance.
- Good Temperature Control.
- Minimum weight in Class
₹831.00 (Price is Exclusive of GST)Pro-Range 3.7V 2200mAh 25C 1S Lithium Polymer Battery Pack
₹831.00 (Price is Exclusive of GST) -
Orange 7.4V 1000mAh 20C 2S Airsoft Lithium Polymer Battery Pack
- Weight: 51 gm.
- Output Voltage:Â 7.4V.
- Dimensions : 102 x 20 x 10 (LxWxH) (mm ).
- Max Continuous Discharge : 20C(20A).
- Max Burst Discharge : 40C(25A).
- Balance Plug: JST-XH.
- Discharge Plug: Jst
₹831.00 (Price is Exclusive of GST)Orange 7.4V 1000mAh 20C 2S Airsoft Lithium Polymer Battery Pack
₹831.00 (Price is Exclusive of GST) -
PANASONIC NCR18650B 3350mAh (1c) LI-ION BATTERY – A grade
- Brand: PANASONIC
- Model:Â NCR18650Â B
- Rated voltage: 3.6-4.2 V
- Battery Capacity: 3350 mAh
- Charging time; Standard charge 4hours/100mA deadline
- Quick charge: 2hours/100mA deadline (25 °C)
- Dimension: As per the Standard 18650 Battery
₹831.00 (Price is Exclusive of GST)PANASONIC NCR18650B 3350mAh (1c) LI-ION BATTERY – A grade
₹831.00 (Price is Exclusive of GST)
