-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹638.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹638.00(Price is Exclusive of GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹264.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹264.00 (Price is Exclusive of GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST) -
ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (Price is Exclusive of GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (Price is Exclusive of GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹207.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹207.00 (Price is Exclusive of GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)
-
₹370.00 (Price is Exclusive of GST)Zener Diode Kit 300pcs 30 Values 0.5W 2V0-39V
₹370.00 (Price is Exclusive of GST) -
Gas Detection Alarm Sensor DIY Kit
Function Description:
With the continuous improvement of people’s living standards, gas and natural gas have entered thousands of households, bringing convenience to everyone but also posing many safety hazards. Gas poisoning accidents also occur from time to time. Therefore, we must conduct regular inspections of areas where gas leakage may occur. The gas detection and alarm circuit is composed of gas sensor MQ5, voltage comparator LM393, voice chip COO2, and other components. It can detect combustible gases in the air and automatically sound and light alarms₹225.00 (Price is Exclusive of GST)Gas Detection Alarm Sensor DIY Kit
₹225.00 (Price is Exclusive of GST) -
High Current Active Alarm Buzzer Driver Module
- Operating voltage 3.3V-5V
- PCB Dimension: 3.1cm*1.3cm.
- Color: Blue
- Easy to use
₹35.00 (Price is Exclusive of GST)High Current Active Alarm Buzzer Driver Module
₹35.00 (Price is Exclusive of GST) -
Sensor Shield V5 Expansion Board For Arduino
- Retain the merits of the V4.0 version
- Laminated design
- PCB immersion gold processing technology
- IIC interface
- Bluetooth module communication interface
- SD card module communication interface
- APC220 wireless rf modules communication interface
- RB URF v1.1 ultrasonic sensors interface
- 12864 LCD string of line and parallel interface
- 32 servo controller interface
₹65.00₹70.00(Price is Exclusive of GST)Sensor Shield V5 Expansion Board For Arduino
₹65.00₹70.00(Price is Exclusive of GST) -
Creality Ender 5 Plus 3D Printer
Features:
- Cubic-like Frame designed
- Ultra Large Printing Format
- Stable Printing
- Filament Sensor
- Resume printing Function
₹47,576.00 (Price is Exclusive of GST)Creality Ender 5 Plus 3D Printer
₹47,576.00 (Price is Exclusive of GST) -
DC Female jack connector
Features:
- It is a perfect solution for those who want to make custom power cable.
- This CCTV Camera DC Power Connector will provide a great connection.
Female Jack Description:
- 5.5mm x 2.1mm Female power plug connector.
- The external diameter of the plug: 5.5mm.
- The internal diameter of the plug: 2.1mm.
- Dimension: 38mm(L) x 14mm(W) x 13mm(H).
₹15.00 (Price is Exclusive of GST)DC Female jack connector
₹15.00 (Price is Exclusive of GST) -
5V 8 Channel Relay Module
Features:
- The 8550 transistor drive, drive ability.
- A fixed bolt holes for easy installation.
- It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red)
- Relay control interface by single-chip IO.
- Low-level suction close, high-level release.
- Easy to use, simple 3 line structure.
₹285.00 (Price is Exclusive of GST)5V 8 Channel Relay Module
₹285.00 (Price is Exclusive of GST) -
LX-103 Light Meter Luxmeter, Measures Up-To 2,00,000 LUX/20,000 FC
Features Of HTC LX-103 Digital Lux Meter:
- Large Range up to 200000Lux
- Large LCD Display with Back Light and Bar Graph
- Auto Power Off
- MAX/MIN and Data Hold
₹2,015.00 (Price is Exclusive of GST)LX-103 Light Meter Luxmeter, Measures Up-To 2,00,000 LUX/20,000 FC
₹2,015.00 (Price is Exclusive of GST) -
30A Intelligent LCD Solar Controller
Features:
- Built-In Industrial Micro Controller
- Big LCD Display
- Full 4 Stage PWM Charge Management
- Dual MOSFET Reverse Current Protection
- Low Heat Production
₹376.00 (Price is Exclusive of GST)30A Intelligent LCD Solar Controller
₹376.00 (Price is Exclusive of GST) -
SG90 Continuous Rotation 360 Degree Servo Motor
Features :
- High resolution
- Accurate positioning
- Fast control response
- Constant torque throughout the servo travel range
- Excellent holding power
₹120.00 (Price is Exclusive of GST)SG90 Continuous Rotation 360 Degree Servo Motor
₹120.00 (Price is Exclusive of GST) -
Voltage Detection Sensor Module 25V
Features :
- Output Interface: “+ ” connected 5/3.3V, “-” connected GND, “s” connected Arduino AD pins
- DC input interface: red terminal positive with VCC, negative with GND
- You can also use the IICLCD1602 LCD to display voltage.
- By 3P connector, connect this module with the expansion of board Arduino, not only makes it easier for you to detect voltage battery.
₹13.00 (Price is Exclusive of GST)Voltage Detection Sensor Module 25V
₹13.00 (Price is Exclusive of GST) -
eSun PLA+ 1.75mm 3D Printing Filament 1kg-Red
Features:
- Consistently High Quality
- Made from great, high-performance materials
- Ready to print on any open source desktop or industrial printer
- Deliver exceptional performance
- 100% bio-degradable and FDA food safety approved
- 10 times stronger than regular PLA on the market
- No wire-drawing problems, the surface of the printouts will be smoother and more delicate
- No cracking problem and brittle issue
- Low material shrinkage rate, uniform diameter
Printing Settings:
- Best Printing Temperature：200-220℃
- Bed Temperature：0-70℃
- Printing Speed：30~90mm/s
- Movement Speed ：90~150mm/s
Maintenance tips:
- Please put the unprinted material in sealed bags, then place it in a cool and dry place to prevent moisture.
- Please insert the wire into the fixed hole of the tray when you don’t use it in case of knotting.
- ABS will produce a slight irritating smell, please print in a well-ventilated environment.
₹1,090.00 (Price is Exclusive of GST)eSun PLA+ 1.75mm 3D Printing Filament 1kg-Red
₹1,090.00 (Price is Exclusive of GST)
