-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹638.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹638.00(Price is Exclusive of GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹264.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹264.00 (Price is Exclusive of GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST) -
ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (Price is Exclusive of GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (Price is Exclusive of GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹207.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹207.00 (Price is Exclusive of GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)
-
ELM327 OBD2 Bluetooth Interface Auto Car Scanner V1.5
Functions:
- Read diagnostic trouble codes, both generic and manufacturer-specific, and display their meaning (over 3000 generic code definitions in the database).
- Clear trouble codes and turn off the MIL (“Check Engine” light)
- Display current sensor data, including:
- Engine RPM
- Calculated Load Value
- Coolant Temperature
- Fuel System Status
- Vehicle Speed
- Short Term Fuel Trim
- Long Term Fuel Trim
- Intake Manifold Pressure
- Timing Advance
- Intake Air Temperature
- Air Flow Rate
- Absolute Throttle Position
- Oxygen sensor voltages/associated short term fuel trims
- Fuel System status
- Fuel Pressure.
Specifications and Features:
1. Works with all OBD-II compliant vehicles.2. Wireless (Bluetooth).3. Software included for Palm, PDA.4. Software included for Windows PC.5. Software included for Windows Smartphone.6. Supports ISO 9141, KWP2000.7. Supports SAE J1850.8. Supports CAN bus.10. Colour: White.₹647.60 (Price is Exclusive of GST)ELM327 OBD2 Bluetooth Interface Auto Car Scanner V1.5
₹647.60 (Price is Exclusive of GST) -
Waveshare 320×240 Resistive Touch LCD Display (2.8 Inch)
Features:
- Onboard touch controller, smoother touch experience than solutions that directly use AD pins for touching.
- SPI interface requires a few pins.
- Programmable backlight control, power saving.
- Comes with development resources and a manual (examples for STM32/AVR/PIC).
₹1,220.00 (Price is Exclusive of GST)Waveshare 320×240 Resistive Touch LCD Display (2.8 Inch)
₹1,220.00 (Price is Exclusive of GST) -
ORANGE 3296W Adjustable Potentiometer Kit- 50PCS
Features:
- Used in the fields of electronic products.
-
High precision mechanism design offers acute operation and long service life.
-
Compact and lightweight, easy to carry and dismantling.
₹670.00 (Price is Exclusive of GST)ORANGE 3296W Adjustable Potentiometer Kit- 50PCS
₹670.00 (Price is Exclusive of GST) -
Orange Quick Two-Port Butt Press Test CH-2 250V Connector Kit- 55PCS
Features:
- The shell is made from high standard flame retardant engineering plastic, practical and long service life
- With a good-quality steel clamp pin of good elasticity and good conductive copper core, connectors can serve their purpose well
- Fast wire connection operation without drilling screw holes speeds up the wiring process, quite convenient
- Connect the live wire to the part with l sign, and neutral wire to the part with n sign, the sign is clearly visible
- There are 55 quick connectors and you can replace joints and electrical taping with these connectors
- The connectors can be reused and stored in a plastic box provided.
₹330.00 (Price is Exclusive of GST)Orange Quick Two-Port Butt Press Test CH-2 250V Connector Kit- 55PCS
₹330.00 (Price is Exclusive of GST) -
ORANGE Small Car Blade Fuse Clippers Kit- 120PCS
Kit Includes:
12 x 2A Blade Fuse
12 x 3A Blade Fuse
12 x 5A Blade Fuse
12 x 7.5A Blade Fuse
12 x 10A Blade Fuse
12 x 15A Blade Fuse
12 x 20A Blade Fuse
12 x 25A Blade Fuse
12 x 30A Blade Fuse
12 x 35A Blade Fuse
₹365.00 (Price is Exclusive of GST)ORANGE Small Car Blade Fuse Clippers Kit- 120PCS
₹365.00 (Price is Exclusive of GST) -
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
Features :
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
₹100.00 (Price is Exclusive of GST)CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
₹100.00 (Price is Exclusive of GST) -
STM32F401CCU6 Minimum System Board Microcomputer STM32 ARM Core Board
Features :
- 100% Brand new and high-quality STM32 Board
- 84 MHz work frequency.
- 256K flash memory,64K SRAM.
- 1.7-3.6V power, I/O.
- 4-26MHz crystal.
- Onboard the Type-C USB interface, you can give the board power supply and USB communication.
₹238.20 (Price is Exclusive of GST)STM32F401CCU6 Minimum System Board Microcomputer STM32 ARM Core Board
₹238.20 (Price is Exclusive of GST) -
Lemon Lithium Polymer Battery Pack 1800mAh 3S 45C/90C
Features:
- Guaranteed leak proof operation in any position except inverted
- The expected life span of two to three years in float service applications
- Operation in a broad range of ambient temperatures
- Recovery capabilities even after deep discharges
- Compact, quick and simple to install, require low maintenance
₹1,610.00 (Price is Exclusive of GST)Lemon Lithium Polymer Battery Pack 1800mAh 3S 45C/90C
₹1,610.00 (Price is Exclusive of GST) -
Creality Ender 3 V2 3D Printer
It’s the same old Ender-3 3D Printer experience, improved with current hardware that includes a 32-bit mainboard, silent stepper motor drivers, a much cleaner appearance and design, plus plenty of other, smaller, touches.
Features:
- Integrated Compact Design
- Multiple improved upgrades
- Ultra silent printing
₹17,170.00 (Price is Exclusive of GST)Creality Ender 3 V2 3D Printer
₹17,170.00 (Price is Exclusive of GST) -
Orange Lithium Polymer Battery Pack 3300mAh 2S 25C/50C (7.4V)
Safety Precautions :
- Avoid over-charging or over-discharging the batteries.
- Do n0t put it beside the high-temperature condition.
- Don’t throw it into the fire or Water
Features :
- Product Type: Lithium Polymer Battery Pack
- The Orange LiPo battery has matched resistance.
- Good Temperature Control.
- Minimum weight in Class
₹1,595.00 (Price is Exclusive of GST)Orange Lithium Polymer Battery Pack 3300mAh 2S 25C/50C (7.4V)
₹1,595.00 (Price is Exclusive of GST) -
Orange Lithium Polymer Battery Pack 1800mAh 3S 40C/80C (11.1V)
Precautions :
- Avoid over-charging or over-discharging the batteries.
- Do n0t put it beside the high-temperature condition.
- Don’t throw it into the fire or Water
Features :
- Product Type: Lithium Polymer Battery Pack
- The Orange LiPo battery has matched resistance.
- Good Temperature Control.
- Minimum weight in Class
₹1,345.00 (Price is Exclusive of GST)Orange Lithium Polymer Battery Pack 1800mAh 3S 40C/80C (11.1V)
₹1,345.00 (Price is Exclusive of GST) -
Orange Lithium Polymer battery Pack 2200mAh 2S 30C/60C (7.4V)
Safety Precautions :
- Avoid over-charging or over-discharging the batteries.
- Do n0t put it beside the high-temperature condition.
- Don’t throw it into the fire or Water
Features :
- Product Type: Lithium Polymer Battery Pack
- The Orange LiPo battery has matched resistance.
- Good Temperature Control.
- Minimum weight in Class
₹1,010.00 (Price is Exclusive of GST)Orange Lithium Polymer battery Pack 2200mAh 2S 30C/60C (7.4V)
₹1,010.00 (Price is Exclusive of GST)
