No products in the cart.
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹390.00 (Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (Price is Exclusive of GST)
TB6612 Motor Driver Module
Motor Driver Module
- Output current: Iout=1.2A(average) / 3.2A (peak)
- Standby control to save power
- CW/CCW/short break/stop motor control modes
- Built-in thermal shutdown circuit and a low voltage detecting circuit
- All pins of the TB6612FNG broken out to 0.1″ spaced pins
- Filtering capacitors on both supply lines
₹195.00 (Price is Exclusive of GST)TB6612 Motor Driver Module
₹195.00 (Price is Exclusive of GST)CN3791 12V MPPT Solar Charger Module
CN3791 12V MPPT Solar Charger Module
Features:
- Maximum Power Point Tracking (MPPT) Solar Charger Module
- 2-Pin JST Connectors for Solar Panel and Battery Connection
- PWM Switching Frequency of 300KHz
- Maximum Charging Current of 2A
₹195.00 (Price is Exclusive of GST)CN3791 12V MPPT Solar Charger Module
₹195.00 (Price is Exclusive of GST)TEC1 12706 Thermoelectric Cooler 6A Peltier Module
Features:
Colour: white
Material: plastic + ceramics
Rated voltage: 12v
Rated power: 50~72w₹200.00 (Price is Exclusive of GST)TEC1 12706 Thermoelectric Cooler 6A Peltier Module
₹200.00 (Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (Price is Exclusive of GST)Stanley 84-214-22 Wire Stripper 130mm
- Size: 130mm / 5 1/4- Inch
- Convenient hole for looping or bending wire
- Ideal for cutting, stripping speaker wire, appliance cords, etc
- Slide adjust for various gauge wire
₹200.00 (Price is Exclusive of GST)Stanley 84-214-22 Wire Stripper 130mm
₹200.00 (Price is Exclusive of GST)51-152 Steel Shaft Claw Hammer
- Shaft 15% longer for better balance and control
- Soft grip ergonomic handle for comfort and grip
- Fully heat treated carbon steel head for strength,durability and safety
₹200.00 (Price is Exclusive of GST)51-152 Steel Shaft Claw Hammer
₹200.00 (Price is Exclusive of GST)EM-18 RFID Reader module
- Operating Voltage: 5V DC Supply
- Reading Distance: 6-10 cm.
- Read frequency: 125 kHz.
- EM4001 64 – bit RFID tag compatible.
- 9600bps ASCII output.
- Current : <50 mA
- Operating Frequency : 125 Khz
- Read Distance : 5 cm
- Compatible Tags : 125KHz EM4100 Tags
₹200.00 (Price is Exclusive of GST)EM-18 RFID Reader module
₹200.00 (Price is Exclusive of GST)Aluminum Electrolytic Capacitor Assorted Kit – 12 Kinds 0.22-F-470-F
Features:
1.Made of high-quality material, durable, and practical to use.
2.Durable and easy to install.
3.Very convenient and practical.
4.Very popular with electronics enthusiasts.
5.A variety of types of electrolytic capacitors to meet your different needs.₹200.00 (Price is Exclusive of GST)Aluminum Electrolytic Capacitor Assorted Kit – 12 Kinds 0.22-F-470-F
₹200.00 (Price is Exclusive of GST)WeMos d1 Mini- IOT ESP8266 Based Development Board
- Specification and Features :-
- 11 digital input/output pins, all pins have interrupt/pwm/I2C/one-wire supported(except D0)
- 1 analog input(3.2V max input)
- Micro USB connection
- Use BRT (Bias Resistor Transistor), easier into flash mode.
- 30% increase in radiating area, more stable.
- Dimensions : 35 x 26 x 8 (LxWxH) mm.
- Weight: 10 gm.
- Board Color : Blue
- Compatible with Arduino
- Compatible with NodeMCU
- Compatible with MicroPython
₹200.00 (Price is Exclusive of GST)WeMos d1 Mini- IOT ESP8266 Based Development Board
₹200.00 (Price is Exclusive of GST)- Specification and Features :-
Tactile DIP Switch Black (10 types -200pcs)
Features :
- Through-hole design.
- Shaft Shape: Round
- Base Size (mm): 6mm
- Middle stroke (1.05mm)
- Shaft Size: 10 different Size (find the details in Package Includes section below)
- High operating force (3.0N or 3.6N) suited to automotive equipment requirements
- The long life of 300,000 cycles realized despite the high operating force
- Used in the fields of electronic products, household appliances, and more.
- High precision mechanism design offers acute operation and long service life.
- Compact and lightweight, easy to carry and dismantling.
- Good electrical conductivity.
₹200.00 (Price is Exclusive of GST)Tactile DIP Switch Black (10 types -200pcs)
₹200.00 (Price is Exclusive of GST)Multi-Functional 3 IN 1 Folding Handheld Magnifier 2 LED Bulb Light Magnifying Glass Maps Jewellery Reading 3x Page Magnifier (Black)
Features:
- Help to solder
- Free your hands
- Made from steel.
- Adjustable clamp
- Compact and easy to carry
₹200.00 (Price is Exclusive of GST)Multi-Functional 3 IN 1 Folding Handheld Magnifier 2 LED Bulb Light Magnifying Glass Maps Jewellery Reading 3x Page Magnifier (Black)
₹200.00 (Price is Exclusive of GST)GT2 Aluminium Timing Pulley 60 teeth 5mm Bore
GT2 toothed pulley with 2mm pitch teeth, suitable for use with GT2 neoprene reinforced nylon or steel reinforced polyurethane belts to be chosen depending on the type of end use. Made entirely of aluminium.
Such a pulley reduces backwash due to accelerations and directional changes, ensuring good resolution when used on automatic system such as 3D printer and small CNC systems.
Features:
- High Quality Aluminium
- Excellently Machined
- Durable and practical
- Minimizes the chance of the belt slipping
- Easy to use
₹205.00 (Price is Exclusive of GST)GT2 Aluminium Timing Pulley 60 teeth 5mm Bore
₹205.00 (Price is Exclusive of GST)
