-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
9V Watt Battery
- Constant 9V Output till lasts.
- Metal Jacket Body.
- Easy to install and Replace
- Pack of 2 Battery.
₹18.00 (excl. GST)9V Watt Battery
₹18.00 (excl. GST) -
GL-12 840 Hole Solderless Breadboard
- Product model: GL-12
- Product pitch: 840 holes
- Excellent quality breadboard.
- ABS plastic material.
- Reusable for fast build a prototype of an electronic circuit
₹45.00₹65.00(excl. GST)GL-12 840 Hole Solderless Breadboard
₹45.00₹65.00(excl. GST) -
DT830D Small Digital Multimeter
- A portable, general purpose digital volt meter multimeter to test wires, batteries, cells, fuses and other electrical components
- Includes large, easy-to-read LCD screen and accurately measures resistance, current and voltage with maximum reading up to 1999
- Red and black leads to test electrical system components including diodes, transistors, wires, fuses
- Checks continuity of wires, fuses and electrical system components
- Built-in overload protector keeps the meter from any possible damage
- Digital AC/DC millimeter with diode and transistor test function
₹140.00 (excl. GST)DT830D Small Digital Multimeter
₹140.00 (excl. GST) -
400 Points Breadboard
Features:
Material: abs plastic and tinned phosphor bronze
Uses: experiment, testing, robot
Self adhesive
Perfect for Arduino shield prototyping and testing₹39.00 (excl. GST)400 Points Breadboard
₹39.00 (excl. GST) -
25W Soldering Rod Iron
- Attains full operating Temperature within a seconds.
- Maintains constant tip temperature.
- Low Leakage Current.
- Safe for the use on dedicated and sensitive Components.
- Maximum Heat transfer efficiency.
- Slide on a Replaceable tip.
- Cool Grip Insulating Nylon Handle
- High Quality Built Material.
-
170 Points Mini Bread Board
- 170 Tie-points for Arduino Raspberry Pi
- Colour May Vary
- Great addition to your hobby craft tool kit
- Perfect product for your saftey and lab supply
- ABS Plastic material
₹15.00₹25.00(excl. GST)170 Points Mini Bread Board
₹15.00₹25.00(excl. GST) -
11.1V 2200mAh Lipo Lithium Polymer Rechargeable Battery
- Lithium-Polymer (Li-Po) Battery For RC, Planes and Drones
- 3 Cell (3S) 11.1V 2200MAH 35C
- Very Small in size and weight
- Connector Plug: XT60 Plug connector
- Discharge Current: 35*2200maH = 77Amp
₹1,500.00 (excl. GST)11.1V 2200mAh Lipo Lithium Polymer Rechargeable Battery
₹1,500.00 (excl. GST) -
Universal Swivel Casters Wheel
Features:
Wheel Type : White Nylon, Dual roller bearing
Load bearing: 10kg
Hole diameter: 4mm
Material: White Nylon PP Material And Steel₹30.00 (excl. GST)Universal Swivel Casters Wheel
₹30.00 (excl. GST) -
Servo Motor SG90 Mini – 180 degree Rotation Standard Quality
- Model: SG90
- Weight: 9 gm
- Operating voltage: 3.0V~ 7.2V
- Servo Plug: JR
- Stall torque @4.8V : 1.2kg-cm
- Stall torque @6.6V : 1.6kg-cm
₹65.00₹110.00(excl. GST)Servo Motor SG90 Mini – 180 degree Rotation Standard Quality
₹65.00₹110.00(excl. GST) -
Servo Motor S3003
Features:
SMT Contruction Surface Mount Technology improves reliability in applications where there is vibration.
Through-the-hole Circuit Board Plating Eliminates the need for wires or leads.
Heavy Duty Output Shaft Designed not to break, and offers versatility when installing the servo horn.
Nylon gears.₹250.00 (excl. GST)Servo Motor S3003
₹250.00 (excl. GST) -
Servo Motor MG995 Metal Gear 180 Degree
- Standard Mini Micro Servo Gear
- Compliant with most standard receiver connector: Futaba, Hitec, Sanwa, GWS.
- Stable and Shock Proof
- Connector Wire Length 300mm
- Power Supply: Through External Adapter
-
Quadcopter Drone DIY Kit – V1
- Built from quality glass fiber and polyamide nylon.
- Integrated PCB connections for direct soldering of your ESCs
- Pre-threaded brass sleeves for all of the frame bolts.
- Colored arms for orientation to keep you flying in the right direction.
- Large mounting tabs on main frame bottom plate for easy camera mounting.
- Easy assembly.
₹10,500.00 (excl. GST)Quadcopter Drone DIY Kit – V1
₹10,500.00 (excl. GST)
