-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
IMAX B3 7-4V 11-1V Lithium Lipo RC Battery Balance Charge
Input voltage: AC 110V-240V
Balance charge current: 850mA
Display: Green & Red LED
Case: Plastic
Max charge power:10WBalance Charger for 7.4V-11.1V
₹315.00 (excl. GST)IMAX B3 7-4V 11-1V Lithium Lipo RC Battery Balance Charge
₹315.00 (excl. GST) -
N30 High Magnetic Motor with Propeller (Set of 2)
- Axis diameter:1mm
- Axis length:8mm
- Electrical size:20*10*12mm
₹170.00 (excl. GST)N30 High Magnetic Motor with Propeller (Set of 2)
₹170.00 (excl. GST) -
MG90S Metal Geared Micro Servo Motor
Applications:
Used as actuators in many robots like Biped Robot, Hexapod, robotic arm etc..
Commonly used for steering system in RC toys
Robots where position control is required without feedback
Less weight hence used in multi DOF robots like humanoid robots
Can be used in DIY Kit for hobby projects₹155.00 (excl. GST)MG90S Metal Geared Micro Servo Motor
₹155.00 (excl. GST) -
Metal Robot Chassis for 4WD Robo Car
- Â Metal Body
- Available in two color red & grey
- Many perforated holes have given for easy attachment of the development board and sensors
- Center Shaft gear motor and side shaft gear motor can be used for this chassis.
₹85.00 (excl. GST)Metal Robot Chassis for 4WD Robo Car
₹85.00 (excl. GST) -
Metal Robot Chassis for 2WD Robo Car
- Drive: 2WD
- Frame:1.5mm aluminum alloy structure, lightweight and high strength
- Working voltage: 4.5~6v
- Lightweight
- Low-cost
- High strength
- Material: Aluminum
₹70.00₹85.00(excl. GST)Metal Robot Chassis for 2WD Robo Car
₹70.00₹85.00(excl. GST) -
L clamp for Johnson Gear Motor Mounting
- Material: Mild Steel
- Thickness: 1.5 mm
- Motor Mounting Hole: 3 mm
- Bracket Mounting Hole: 3 mm
- Weight: 18 gm (each)
₹12.00 (excl. GST)L clamp for Johnson Gear Motor Mounting
₹12.00 (excl. GST) -
100 RPM Johnson Geared Motor
- Base Motor RPM: 18000
- Operating Voltage: 6-18 V
- Rated Voltage: 12 V
- Rated Torque: 5.7 kg-cm
- Stall Torque: 37.6 kg-cm
- Gearbox Dimensions: 25×37 (LxW) mm
₹315.00 (excl. GST)100 RPM Johnson Geared Motor
₹315.00 (excl. GST) -
Flysky FS-I610 channel 2.4GHz AFHDS RC Transmitter with FS-iA6B Receiver
Features:
This radio system uses a high gain and multi directional antenna ;\Power: 6V (1.5V AA*4) ;
Transmitting Power:Â 20dBm ;
RF Receiver Sensitivity: -105dbm ;
Low Voltage Warning (V):Â 4.2
₹4,900.00 (excl. GST)Flysky FS-I610 channel 2.4GHz AFHDS RC Transmitter with FS-iA6B Receiver
₹4,900.00 (excl. GST) -
₹3,900.00 (excl. GST)Flysky CT6B Remote 6 Channel Transmitter and Receiver
₹3,900.00 (excl. GST) -
Durable Rubber Tire Yellow BO Motor Wheel
- Tire with sponge liner for more strength
- With upgraded tire tread for greater friction
- New design wheel for better combination with the motor
- Diameter: 65 mm
- Width : 28 mm
- The material of Wheel: High-strength plastic
- The material of Tyre: Rubber
- Color: Yellow
₹28.00 (excl. GST)Durable Rubber Tire Yellow BO Motor Wheel
₹28.00 (excl. GST) -
DC Pump 24V 150PSI for Mist Fog Spray in Sanitizer Dispenser Tunnel
- Watering configuration: much the same, additional sprinklers and timers are required
- The price is the price of a pump, without other accessories
- Maximum pressure: 0.48MP.
₹1,500.00 (excl. GST)DC Pump 24V 150PSI for Mist Fog Spray in Sanitizer Dispenser Tunnel
₹1,500.00 (excl. GST) -
DC Motor 2000 RPM – 3V to 6V
Features:
Length: 25mm
Diameter:21mm
Shaft Diameter:2mm
Shaft Length:9mm
Voltage:3-5V₹20.00 (excl. GST)DC Motor 2000 RPM – 3V to 6V
₹20.00 (excl. GST)
