No products in the cart.
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹390.00 (Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (Price is Exclusive of GST)
GT2 Open Loop Timing Belt 6mm Width for 3D Printer-5 Meter
GT2 Open Loop Timing Belt
Features:
- Precision registration and timing with no loss of high torque carrying capability
- Minimal vibration and chordal effectPositive slip proof engagement
- Wide speed range, especially important when the entire speed range is developed from a single source
- Virtually no elongation (stretching) due to wear
- Power transmission efficiency is not lost with the use
- A clean operation, no need for lubrication
- Reduced noise.
- Long, dependable trouble-free service.
₹485.00 (Price is Exclusive of GST)GT2 Open Loop Timing Belt 6mm Width for 3D Printer-5 Meter
₹485.00 (Price is Exclusive of GST)- ₹490.00 (Price is Exclusive of GST)
4-Axis Multi-Rotor Quadcopter Frame – F450
₹490.00 (Price is Exclusive of GST) 555 Timer based Electronics Project DIY Kit
- The component kit for engineering project consists of high quality products that are very important for prototyping and testing.
- These electronic kit component consists of assorted resistors, transistors, capacitors, diodes, breadboard, wires, buttons and switch.
- The collection of electronic components comes in very handy for both beginners and project enthusiasts.
₹495.00 (Price is Exclusive of GST)555 Timer based Electronics Project DIY Kit
₹495.00 (Price is Exclusive of GST)ESP32 Development Board CP2102 based
- Bluetooth Ultra-Low Power Consumption Dual Core
- Durable Product
- It has 38 PIN
₹500.00 (Price is Exclusive of GST)ESP32 Development Board CP2102 based
₹500.00 (Price is Exclusive of GST)2.4″ Inch Touch Screen TFT Display Shield
- 2.4″ Touch LCD TFT display module for Arduino
- 240*320 pixels resolution
- Ability to display 262000 different colors
- The shield comes equipped with a microSD card slot.
- SPFD5408 controller with built-in video RAM buffer
₹500.00 (Price is Exclusive of GST)2.4″ Inch Touch Screen TFT Display Shield
₹500.00 (Price is Exclusive of GST)0-83-034 Max Steel C-Clamp
- High-visibility, corrosion-resistant finish
- Advanced frame design resists flexing and bending
- Heavy duty malleable iron and steel construction
- Roll formed screw threads ensures smooth operation and durability
₹500.00 (Price is Exclusive of GST)0-83-034 Max Steel C-Clamp
₹500.00 (Price is Exclusive of GST)Arduino LilyPad ATmega328P compatible Board
Features :
- Board will run from 2V to 5V.
- The latest version of the LilyPad supports automatic reset for even easier programming.
- The backside of the LilyPad is now completely flat!
- We now use a surface mount programming connector to keep the header from poking through.
- This version of the LilyPad now uses the new ATmega328 at 8MHz.
- Arduino 0016 supports the Pro Mini Arduino 328/8MHz/16MHZ.
- Use this setting when using this new LilyPad 328.
₹500.00 (Price is Exclusive of GST)Arduino LilyPad ATmega328P compatible Board
₹500.00 (Price is Exclusive of GST)Human Induction Fan Model Kit
The body sensing fan, in short, automatically turns on the fan when the body sensing module senses someone. When a person leaves the human body sensing module, the fan will automatically turn off, which is very intelligent.
₹500.00 (Price is Exclusive of GST)Human Induction Fan Model Kit
₹500.00 (Price is Exclusive of GST)LM317 Adjustable Voltage Power Supply Board Learning Kit
LM317 Power Supply Board
It is an AC-DC 110V to 1.25V-12V LM317 Adjustable Step Down Power Supply Buck Voltage Converter LED Display DIY Kit.It can output stable voltage. Users can change output by operating a potentiometer.It also can be used as a signal generator or logic circuit or buzzer alarm circuit.₹500.00 (Price is Exclusive of GST)LM317 Adjustable Voltage Power Supply Board Learning Kit
₹500.00 (Price is Exclusive of GST)Pro-Range INR 18650 P28A 3.7V 2800mAh 1S1P 25A/30A Discharge Li-ion Drone Battery Pack
- Nominal Capacity (mAh): 2800
- Nominal Voltage (v): 3.7
- Max Charging Voltage (v): 4.2
- Charge Port: 2 Pin JST XH
- Discharge Port: Open wire
₹502.00 (Price is Exclusive of GST)Pro-Range INR 18650 P28A 3.7V 2800mAh 1S1P 25A/30A Discharge Li-ion Drone Battery Pack
₹502.00 (Price is Exclusive of GST)GKON Bluetooth Speaker Device
Bluetooth is a short range wireless communication technology that is both robust and energy-efficient. The technology allows easy wireless connection to other Bluetooth devices, so you can play your favorite music from any smartphones, tablets or even laptops including iPod or iPhone on Bluetooth-enabled speaker easily.
₹515.00 (Price is Exclusive of GST)GKON Bluetooth Speaker Device
₹515.00 (Price is Exclusive of GST)ESP32 CAM WiFi Module Bluetooth with OV2640 Camera Module 2MP For Face Recognization
Features :
ESP32-CAM :
- The smallest 802.11b/g/n Wi-Fi BT SoC module.
- Low power 32-bit CPU, can also serve the application processor.
- Up to 160MHz clock speed, summary computing power up to 600 DMIPS.
- Built-in 520 KB SRAM, external 4MPSRAM.
- Supports UART/SPI/I2C/PWM/ADC/DAC.
- Support OV2640 and OV7670 cameras, built-in flash lamp.
- Support image WiFI upload.
- Supports TF card.
- Supports multiple sleep modes.
- Embedded Lwip and FreeRTOS.
- Supports STA/AP/STA+AP operation mode.
- Support Smart Config/AirKiss technology.
- Support for serial port local and remote firmware upgrades (FOTA).
Specifications :
- Wireless Module: ESP32-S WiFi 802.11 b/g/n + Bluetooth 4.2 LE module with PCB antenna, u.FL connector, 32Mbit SPI flash, 4MBit PSRAM.
- External Storage: micro SD card slot up to 4GB.
- Camera
- FPC connector.
- Support for OV2640 (sold with a board) or OV7670 cameras.
- Image Format: JPEG( OV2640 support only ), BMP, grayscale.
- LED flashlight.
- Expansion: 16x through-holes with UART, SPI, I2C, PWM.
- Misc: Reset button.
- Power Supply: 5V via pin header.
- Power Consumption.
- Flash LED off: 180mA @ 5V.
- Flash LED on to maximum brightness: 310mA @ 5V.
- Deep-sleep: 6mA @ 5V min.
- Modem-sleep: 20mA @ 5V min.
- Light-sleep: 6.7mA @ 5V min.
- Dimensions (ESP32): 40 x 27 x 12 (LxWxH) mm.
- Temperature Range: Operating: -20 ℃ ~ 85 ℃; storage: -40 ℃ ~ 90 ℃ @ < 90%RH.
₹519.00 (Price is Exclusive of GST)ESP32 CAM WiFi Module Bluetooth with OV2640 Camera Module 2MP For Face Recognization
₹519.00 (Price is Exclusive of GST)
