-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
NEEMA 17-JK42HM48-1684-0.44N-m Round Type
Features :
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
₹1,010.00 (excl. GST)NEEMA 17-JK42HM48-1684-0.44N-m Round Type
₹1,010.00 (excl. GST) -
Waveshare 12-bit I2C 16-Channel Servo Driver for micro:bit
- Power supply: 5V (POWER connector)Â ORÂ 6V~12V (VIN terminal)
- Servo voltage: 5V
- Logic voltage: 3.3V
- Driver: PCA9685
- Control interface: I2C
- Dimension: 65mm x 36mm
- Mounting hole size: 3.0mm
₹1,040.00 (excl. GST)Waveshare 12-bit I2C 16-Channel Servo Driver for micro:bit
₹1,040.00 (excl. GST) -
eSun PLA+ 1.75mm 3D Printing Filament 1kg-Blue
Main Features of PLA+:
eSun High-Quality Filament:
For best 3D printing filament quality always matters, but you don’t have to pay through the nose for a string of plastic. eSun Industrial is an international leader in FDM innovative technologies and their filament is a testament to their dedication to quality and cost-effectiveness. Most PLA colors are glossy and marginally translucent.eSun PLA+ Compatibility:
 Printing Filament blue has a lower melting point, less shrinkage and is non-toxic; making it an ideal material for everyday 3d printing which is compatible with almost all printers in the market.Diameter Consistency:
It’s important that your filament has a very constant diameter if you want to get a great looking print. Variance in filament diameter will result in poor surface quality (primarily on vertical sections) because it produces unwarranted and uncontrollable fluctuations in extrusion rates.eSun promises that their filament has a tolerance of ±0.05mm across all of their rolls that they produce, but in reality, the quality of eSun’s filament far exceeds their listed specifications. You can be confident that your prints will have fantastic surface uniformity and smoothness with eSun.Colors:
A major part of what sparked the popularity in eSun is the rich and vibrant colors of their filaments. Not only are eSun’s colors refined individually, but they also have one of the largest ranges available on the market.Printing Settings:
- Best Printing Temperature：200-220℃
- Bed Temperature：0-70℃
- Printing Speed：30~90mm/s
- Movement Speed ：90~150mm/s
Maintenance tips:
- Please put the unprinted material in sealed bags, then place it in a cool and dry place to prevent moisture.
- Please insert the wire into the fixed hole of the tray when you don’t use it in case of knotting.
- ABS will produce a slight irritating smell, please print in a well-ventilated environment.
₹1,090.00 (excl. GST)eSun PLA+ 1.75mm 3D Printing Filament 1kg-Blue
₹1,090.00 (excl. GST) -
eSun PLA+ 1.75mm 3D Printing Filament 1kg-Silver
Features:
- Consistently High Quality
- Made from great, high-performance materials
- Ready to print on any open source desktop or industrial printer
- Deliver exceptional performance
- 100% bio-degradable and FDA food safety approved
- 10 times stronger than regular PLA on the market
- No wire-drawing problems, the surface of the printouts will be smoother and more delicate
- No cracking problem and brittle issue
- Low material shrinkage rate, uniform diameter
Printing Settings:
- Best Printing Temperature：200-220℃
- Bed Temperature：0-70℃
- Printing Speed：30~90mm/s
- Movement Speed ：90~150mm/s
Maintenance tips:
- Please put the unprinted material in sealed bags, then place it in a cool and dry place to prevent moisture.
- Please insert the wire into the fixed hole of the tray when you don’t use it in case of knotting.
- ABS will produce a slight irritating smell, please print in a well-ventilated environment.
₹1,090.00 (excl. GST)eSun PLA+ 1.75mm 3D Printing Filament 1kg-Silver
₹1,090.00 (excl. GST) -
eSun PLA+ 1.75mm 3D Printing Filament 1kg-Orange
Features:
- Consistently High Quality
- Made from great, high-performance materials
- Ready to print on any open source desktop or industrial printer
- Deliver exceptional performance
- 100% bio-degradable and FDA food safety approved
- 10 times stronger than regular PLA on the market
- No wire-drawing problems, the surface of the printouts will be smoother and more delicate
- No cracking problem and brittle issue
- Low material shrinkage rate, uniform diameter
Printing Settings:
- Best Printing Temperature：200-220℃
- Bed Temperature：0-70℃
- Printing Speed：30~90mm/s
- Movement Speed ：90~150mm/s
Maintenance tips:
- Please put the unprinted material in sealed bags, then place it in a cool and dry place to prevent moisture.
- Please insert the wire into the fixed hole of the tray when you don’t use it in case of knotting.
- ABS will produce a slight irritating smell, please print in a well-ventilated environment.
₹1,090.00 (excl. GST)eSun PLA+ 1.75mm 3D Printing Filament 1kg-Orange
₹1,090.00 (excl. GST) -
eSun PLA+ 1.75mm 3D Printing Filament 1kg-Green
Features:
- Consistently High Quality
- Made from great, high-performance materials
- Ready to print on any open source desktop or industrial printer
- Deliver exceptional performance
- 100% bio-degradable and FDA food safety approved
- 10 times stronger than regular PLA on the market
- No wire-drawing problems, the surface of the printouts will be smoother and more delicate
- No cracking problem and brittle issue
- Low material shrinkage rate, uniform diameter
Printing Settings:
- Best Printing Temperature：200-220℃
- Bed Temperature：0-70℃
- Printing Speed：30~90mm/s
- Movement Speed ：90~150mm/s
Maintenance tips:
- Please put the unprinted material in sealed bags, then place it in a cool and dry place to prevent moisture.
- Please insert the wire into the fixed hole of the tray when you don’t use it in case of knotting.
- ABS will produce a slight irritating smell, please print in a well-ventilated environment.
₹1,090.00 (excl. GST)eSun PLA+ 1.75mm 3D Printing Filament 1kg-Green
₹1,090.00 (excl. GST) -
eSun PLA+ 1.75mm 3D Printing Filament 1kg-Red
Features:
- Consistently High Quality
- Made from great, high-performance materials
- Ready to print on any open source desktop or industrial printer
- Deliver exceptional performance
- 100% bio-degradable and FDA food safety approved
- 10 times stronger than regular PLA on the market
- No wire-drawing problems, the surface of the printouts will be smoother and more delicate
- No cracking problem and brittle issue
- Low material shrinkage rate, uniform diameter
Printing Settings:
- Best Printing Temperature：200-220℃
- Bed Temperature：0-70℃
- Printing Speed：30~90mm/s
- Movement Speed ：90~150mm/s
Maintenance tips:
- Please put the unprinted material in sealed bags, then place it in a cool and dry place to prevent moisture.
- Please insert the wire into the fixed hole of the tray when you don’t use it in case of knotting.
- ABS will produce a slight irritating smell, please print in a well-ventilated environment.
₹1,090.00 (excl. GST)eSun PLA+ 1.75mm 3D Printing Filament 1kg-Red
₹1,090.00 (excl. GST) -
eSun PLA+ 1.75mm 3D Printing Filament 1kg-White
Features:
- Consistently High Quality
- Made from great, high-performance materials
- Ready to print on any open source desktop or industrial printer
- Deliver exceptional performance
- 100% bio-degradable and FDA food safety approved
- 10 times stronger than regular PLA on the market
- No wire-drawing problems, the surface of the printouts will be smoother and more delicate
- No cracking problem and brittle issue
- Low material shrinkage rate, uniform diameter
Printing Settings:
- Best Printing Temperature：200-220℃
- Bed Temperature：0-70℃
- Printing Speed：30~90mm/s
- Movement Speed ：90~150mm/s
Maintenance tips:
- Please put the unprinted material in sealed bags, then place it in a cool and dry place to prevent moisture.
- Please insert the wire into the fixed hole of the tray when you don’t use it in case of knotting.
- ABS will produce a slight irritating smell, please print in a well-ventilated environment.
₹1,090.00 (excl. GST)eSun PLA+ 1.75mm 3D Printing Filament 1kg-White
₹1,090.00 (excl. GST) -
NEEMA 23-JK57HS51-2804-10.1kg-cm Round Type
Features :
- Comparably more powerful than NEMA17 motors.
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
₹1,096.00 (excl. GST)NEEMA 23-JK57HS51-2804-10.1kg-cm Round Type
₹1,096.00 (excl. GST) -
₹1,120.00 (excl. GST)
Quadruped Bionic Smart Robot Dog
₹1,120.00 (excl. GST) -
Emax ECOII-2004-3000KV Brushless Motor
Features:
- NSK precision bearing
- Base casing : Al 7075
- Rotor : N52SH arc magnets
- Steel shaft
- 12*12mm hole pattern
- Multi-strand winding
- 120mm 24 AWG silicone wire
Specifications:
- KV: 3000
- Framework: 12N14P
- Length: 19.2mm
- Diameter: 24.7mm
- Cells: 4-6S
- Propeller: 4″-5″
- Prop adapter Shaft Thread: 1.5mm
- Bearing Shaft: 3mm
- Bolt Pattern: M2 (12x12mm)
- Maximum Thrust: 1170g(on4s)
- Peak Current (6S): 32A
₹1,180.00₹1,599.00(excl. GST)Emax ECOII-2004-3000KV Brushless Motor
₹1,180.00₹1,599.00(excl. GST) -
Taparia PTB16 Compact Plastic Tool Box with Organizer
It Is Available With Metal Rod Hinges That Help You Carry More Load Easily. Store All The Small Objects And Fasteners In The Organiser Sections Available On The Top. It Is Highly Portable And Keeps Your Metal Organized. It Has Latch Type Lock That Locks
₹1,200.00 (excl. GST)Taparia PTB16 Compact Plastic Tool Box with Organizer
₹1,200.00 (excl. GST)
