No products in the cart.
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹390.00 (Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (Price is Exclusive of GST)
₹50.00 (Price is Exclusive of GST)L9110S H Bridge Stepper Motor Dual DC Driver Controller Module
₹50.00 (Price is Exclusive of GST)1Hz-50MHz Crystal Oscillator Frequency Counter DIY Kit LED Digital Frequency Tester Meter
- LED display to show the data clearly.
- Measuring Frequency Range: 1Hz~50MHz; Signal Frequency: Max.30V.
- Can measure the oscillation frequency of most commonly used crystals.
- Automatic range conversion without manual switching.
- Programmable addition and subtraction frequency settings, can measure radio transceiver.
- Warranty not applicable for this product
₹390.00 (Price is Exclusive of GST)1Hz-50MHz Crystal Oscillator Frequency Counter DIY Kit LED Digital Frequency Tester Meter
₹390.00 (Price is Exclusive of GST)4Pcs 50Kg Pressure Micro Scale Weighing Sensor Resistance Strain Half Bridge Sensor Body Load Cell
- Using a sensor with external resistors full bridge measurement range of a sensor range: 50kg; Higher requirements for external resistor
- The use of only two full-bridge sensors measuring range is the range of the two sensors and: 50kgx2 = 100kg Size: 34mm x 34mm
- Package:4 x human scale load cell sensor
₹160.00 (Price is Exclusive of GST)4Pcs 50Kg Pressure Micro Scale Weighing Sensor Resistance Strain Half Bridge Sensor Body Load Cell
₹160.00 (Price is Exclusive of GST)TPA3118 Mono Digital Amplifier Board 60W Home Audio Kit
Applicable speaker impedance: 4-8 ohm(8 ohm is the best). Specifications: Working Voltage: DC 8-24V Power Output: 60W Applicable Speaker Impedance: 4-8 ohm PCB Board Size: 45 * 35mm / 1.77 * 1.4in Weight: 50g / 0.43oz Package List: 1 * TPA3118 Digital Amplifier Board
₹255.00 (Price is Exclusive of GST)TPA3118 Mono Digital Amplifier Board 60W Home Audio Kit
₹255.00 (Price is Exclusive of GST)- ₹120.00 (Price is Exclusive of GST)
Red YB27A LED AC 60-500V Digital Voltmeter Home Use Voltage Display, 2 Wires LED Displays
₹120.00 (Price is Exclusive of GST) NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)- ₹195.00 (Price is Exclusive of GST)
Dual Channel Stereo Mini Class D Digital Audio Power Amplifier Board (PAM8610 2 x 10W with Volume)
₹195.00 (Price is Exclusive of GST) - ₹87.00 (Price is Exclusive of GST)
Yellow 0.28″ Mini 2 Wire Dc Voltmeter 0.2-100v Digital Display Voltmeter Gauge LED Voltage
₹87.00 (Price is Exclusive of GST) ATL Package 4 (DIY Tinkering and Safety Equipments)
The Atal Tinkering Lab (ATL) initiative is aimed at enhancing the Indian Education System. It is converting thoughts to reality, where the young children (max 12 years of age) are being introduced to the world of technological innovation. ATL made to experience totally different microenvironments in Indian schools. This is allowing the children to work around their area of interest without having a fixed syllabus.
₹7,700.00₹8,500.00(Price is Exclusive of GST)ATL Package 4 (DIY Tinkering and Safety Equipments)
₹7,700.00₹8,500.00(Price is Exclusive of GST)ATL Package 3 (Electronics and Mechanical Prototyping Tools)
The Atal Tinkering Lab (ATL) initiative is aimed at enhancing the Indian Education System. It is converting thoughts to reality, where the young children (max 12 years of age) are being introduced to the world of technological innovation. ATL made to experience totally different microenvironments in Indian schools. This is allowing the children to work around their area of interest without having a fixed syllabus.
₹43,000.00 (Price is Exclusive of GST)ATL Package 3 (Electronics and Mechanical Prototyping Tools)
₹43,000.00 (Price is Exclusive of GST)ATL Package 2 (3D Printing, Rapid Prototyping and DIY Crafting)
Package 2 is all about Prototyping at ATL. Unleash your design and prototyping skills with this package.
₹21,500.00 (Price is Exclusive of GST)ATL Package 2 (3D Printing, Rapid Prototyping and DIY Crafting)
₹21,500.00 (Price is Exclusive of GST)Atal Tinkering Lab ATL Package 1 (Electronics Development, Internet of Things & Sensors, Robotics and DIY Kits)
Atal Tinkering Lab ATL Package 1 containing components for Electronics Development, Internet of Things & Sensors, Robotics and DIY Kits.
₹119,000.00₹155,500.00(Price is Exclusive of GST)Atal Tinkering Lab ATL Package 1 (Electronics Development, Internet of Things & Sensors, Robotics and DIY Kits)
₹119,000.00₹155,500.00(Price is Exclusive of GST)
