No products in the cart.
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹390.00 (Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (Price is Exclusive of GST)
RF Wireless Transmitter Receiver Module (Green)
- Operating voltage: 5V.
- Quiescent Current: 4mA.
- Receiving frequency: 315MHz.
- Receiver sensitivity: -105 dB.
- Communication Distance (m): 20 ~ 200 meter.
NodeMcu ESP8266 Based Wireless Development Module for IOT
- Open-source, Interactive, Programmable, Low cost, Simple, Smart, WI-FI enabled
- Arduino-like hardware IO
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management units
- Onboard USB to serial chip to easily program and upload codes from the Arduino IDE
- Embeds logic level converter circuits
- Has onboard 3.3V regulator to ensure enough power to function as your go-to WiFi chip!
- Easy access to the GPIO pins for easy prototyping
- ESP-12E Processor
- Easy to use breadboard friendly form factor
MFRC-522 RC522 RFID Module
- Integrated MF RC522
- 13.56MHz contactless communication card chip.
- The low-voltage, low-cost, small size of the non-contact card chip to read and write.
- Working current：13 – 26mA / DC 3.3V
- Standby current：10 – 13mA / DC 3.3V
- Sleep current：<80uA
- Peak current：<30mA
- Working frequency：13.56MHz
- Card reading distance ：0～60mm （Mifare1 card）
₹125.00 (Price is Exclusive of GST)MFRC-522 RC522 RFID Module
₹125.00 (Price is Exclusive of GST)HC-05 Bluetooth Module
- Bluetooth protocol: Bluetooth Specification v2.0+EDR
- Frequency: 2.4GHz ISM band
- Modulation: GFSK(Gaussian Frequency Shift Keying)
- Emission power: ≤4dBm, Class 2
- Sensitivity: ≤-84dBm at 0.1% BERCSR Bluetooth Chip Solution
- Enhanced Data Rate (EDR) compliant with V2.0.E.2 of the specification for both 2Mbps and 3Mbps modulation modes
₹170.00₹275.00(Price is Exclusive of GST)HC-05 Bluetooth Module
₹170.00₹275.00(Price is Exclusive of GST)Ublox NEO 6M GPS module
- 5Hz position update rate.
- The cold start time of 38 s and Hot start time of 1 s.
- Configurable from 4800 Baud to 115200 Baud rates. (default 9600).
- SuperSense ® Indoor GPS: -162 dBm tracking sensitivity.
- Support SBAS (WAAS, EGNOS, MSAS, GAGAN).
- Separated 18 x 18mm GPS antenna.
₹335.00₹490.00(Price is Exclusive of GST)Ublox NEO 6M GPS module
₹335.00₹490.00(Price is Exclusive of GST)Esp8266-12E WIFI Module
- WS2812 Led on board.
- 802.11 b/g/n
- Wi-Fi Direct (P2P), soft-AP
- Integrated TCP/IP protocol stack
- Integrated TR switch, balun, LNA, power amplifier and matching network
- Integrated PLL, regulators, DCXO and power management units
₹150.00 (Price is Exclusive of GST)Esp8266-12E WIFI Module
₹150.00 (Price is Exclusive of GST)Esp8266-01 Serial WIFI Wireless Transceiver Module
- 802.11 b/g/n Standards
- Wi-Fi Direct (P2P), soft-AP
- 1MB Flash Memory
- Integrated low power 32-bit CPU could be used as an application processor
- A-MPDU & A-MSDU aggregation & 0.4ms guard interval
- Wake up and transmit packets in < 2ms
- Standby power consumption of < 1.0mW (DTIM3)
₹125.00 (Price is Exclusive of GST)Esp8266-01 Serial WIFI Wireless Transceiver Module
₹125.00 (Price is Exclusive of GST)ESP32 Development Board CP2102 based
- Bluetooth Ultra-Low Power Consumption Dual Core
- Durable Product
- It has 38 PIN
₹500.00 (Price is Exclusive of GST)ESP32 Development Board CP2102 based
₹500.00 (Price is Exclusive of GST)ESP-12F ESP8266 Wifi IOT Module
- Communication interface voltage: 3.3V
- Working current: 240mA(MAX)
- Serial port baud rate: 115200 (default), can be modified to other values by AT command
- Serial communication format: 8N1
- Wireless Network Mode: station / softAP / SoftAP + station
- Wireless criteria: 802.11 b / g / n
- WIFI @ 2.4 GHz, support for WPA / WPA2 security mode
- +19.5dBm output power
₹115.00 (Price is Exclusive of GST)ESP-12F ESP8266 Wifi IOT Module
₹115.00 (Price is Exclusive of GST)Wire Cutter and Stripper
- Flawless Finish
- Optimum Strength
- Best Quality
- Cutting range of wire 0.5mm to 2.5mm & 6mm
- Also Suitable for Electronic, Aviation & Automobile sectors
₹65.00 (Price is Exclusive of GST)Wire Cutter and Stripper
₹65.00 (Price is Exclusive of GST)Wire Clipper Nipper
Suitable for dressing components on printed circuit boards. Handles made out of ABS plastics. Diagonal cutters have intersecting jaws that cut the wire at an angle, leaving a flat tip.
₹65.00 (Price is Exclusive of GST)Wire Clipper Nipper
₹65.00 (Price is Exclusive of GST)TP4056 1A Li-ion Lithium Battery Charging Module Charging Board Charger Micro USB
- Input interface: Mini USB.
- Current: 1A adjustable.
- Charge precision: 1.5%.
- Input voltage: 4.5V-5.2V.
- Full charge voltage: 4.2V.
- Battery over-current protection: 3 A
- The battery Undervoltage protection: 2.5 V
₹30.00 (Price is Exclusive of GST)TP4056 1A Li-ion Lithium Battery Charging Module Charging Board Charger Micro USB
₹30.00 (Price is Exclusive of GST)
