-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (excl. GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (excl. GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)
-
KP000 10mm Bore Inner Ball Mounted Pillow Block Insert Bearing
Features :
- Durable with high precision
- Can withstand great weight
- The angle between the inner bearing and the outer fixing ring is adjustable
- Easy to install
₹140.00 (excl. GST)KP000 10mm Bore Inner Ball Mounted Pillow Block Insert Bearing
₹140.00 (excl. GST) -
KP08 8mm Bore Inner Ball Mounted Pillow Block Insert Bearing
Features :
- Durable with high precision
- Can withstand great weight
- The angle between the inner bearing and the outer fixing ring is adjustable
- Easy to install
₹142.00 (excl. GST)KP08 8mm Bore Inner Ball Mounted Pillow Block Insert Bearing
₹142.00 (excl. GST) -
GT2 Timing Idler Pulley 20 Tooth For 6mm Belt 20 Tooth 5mm Bore-2Pcs
For precise motion control, GT2 belts and pulleys offer excellent precision at a great price. This pulley is meant for use with GT2 6mm wide belts only – MXL belts will slip due to the different tooth profiles.
 Features:
- Adopting high-quality Aluminum Alloy material，sturdy and durable
- Adopt surface oxidation treatment, anti-Rust and Anti-corrosion effectively
₹216.00 (excl. GST)GT2 Timing Idler Pulley 20 Tooth For 6mm Belt 20 Tooth 5mm Bore-2Pcs
₹216.00 (excl. GST) -
GT2 Close-Loop Rubber Timing Belt for 3D Printer
Features:
- Type: Closed Loop
- Length: 158 mm
- Width: 6mm
- Good quality and durable low noise
₹75.00 (excl. GST)GT2 Close-Loop Rubber Timing Belt for 3D Printer
₹75.00 (excl. GST) -
Tensioner Torsion Spring for GT2 6MM Timing Belt-5Pcs
Features:
- Maintain optimal belt tension to ensure high-quality prints every time.
- it is compatible with 6mm GT2 timing belts.
- It will absorb belt vibration.
- It can be mounted on top of the belts and requires no removal.
₹80.00 (excl. GST)Tensioner Torsion Spring for GT2 6MM Timing Belt-5Pcs
₹80.00 (excl. GST) -
GT2 Aluminium Timing Pulley 60 teeth 5mm Bore
GT2 toothed pulley with 2mm pitch teeth, suitable for use with GT2 neoprene reinforced nylon or steel reinforced polyurethane belts to be chosen depending on the type of end use. Made entirely of aluminium.
Such a pulley reduces backwash due to accelerations and directional changes, ensuring good resolution when used on automatic system such as 3D printer and small CNC systems.
Features:
- High Quality Aluminium
- Excellently Machined
- Durable and practical
- Minimizes the chance of the belt slipping
- Easy to use
₹205.00 (excl. GST)GT2 Aluminium Timing Pulley 60 teeth 5mm Bore
₹205.00 (excl. GST) -
Aluminum GT2 20 Tooth Timing Pulley 6.35mm Bore For 6mm Belt
FEATURES-
- Material: Aluminum.
- No. of teeth: 20.
- Outer Diameter: 16mm.
- Inner Diameter: 6.35mm.
- Length: 14 mm.
- Weight: 6 gm.
₹125.00 (excl. GST)Aluminum GT2 20 Tooth Timing Pulley 6.35mm Bore For 6mm Belt
₹125.00 (excl. GST) -
EasyMech Bracket For NEMA23 Stepper Motor – Straight
Features :Â
- Most accurate design for NEMA23 Stepper Motor
- Made from High-Quality MS.
- Equips extra holes for user-defined motor fitting.
₹170.00 (excl. GST)EasyMech Bracket For NEMA23 Stepper Motor – Straight
₹170.00 (excl. GST) -
EasyMech Bracket For NEMA 17 Stepper Motor – STRAIGHT
Features :Â
- Most accurate design for NEMA17 Stepper Motor
- Made from High-Quality MS.
- Equips extra holes for user-defined motor fitting.
₹138.00 (excl. GST)EasyMech Bracket For NEMA 17 Stepper Motor – STRAIGHT
₹138.00 (excl. GST) -
Waveshare 4 Inch Resistive HDMI LCD Display 480×800
Features:
- 4inch IPS screen, 480×800 hardware resolution.
- Resistive touch control.
- Compatible and Direct-connect with any revision of Raspberry Pi (except the Pi 1 Model B or Pi Zero, which requires an HDMI cable).
- Drivers provided (works with your own Raspbian/Ubuntu/Kali/Retropie).
- Also works as a computer monitor, in this case, the touch panel is unavailable and an HDMI cable is required.
- HDMI interface for displaying, no I/Os required (however, the touch panel still needs I/Os).
- 3.5mm audio jack, supports HDMI audio output.
- The backlight can be turned off to lower power consumption.
₹2,490.00 (excl. GST)Waveshare 4 Inch Resistive HDMI LCD Display 480×800
₹2,490.00 (excl. GST) -
ORANGE TVS Transient Suppressor Clamp Type P6KE Diode Kit (200PCS )
Features:
- Used in the fields of electronic products, household appliances, and more.
-
High precision mechanism design offers acute operation and long service life.
-
Compact and lightweight, easy to carry and dismantling.
₹640.00 (excl. GST)ORANGE TVS Transient Suppressor Clamp Type P6KE Diode Kit (200PCS )
₹640.00 (excl. GST) -
Orange 100PCS Rectifier/Schottky Diode Kit
Features:
- Used in the fields of electronic products, household appliances, and more.
-
High precision mechanism design offers acute operation and long service life.
-
Compact and lightweight, easy to carry and dismantle.
₹240.00 (excl. GST)Orange 100PCS Rectifier/Schottky Diode Kit
₹240.00 (excl. GST)
