No products in the cart.
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹390.00 (Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (Price is Exclusive of GST)
Official Raspberry Pi M.2 HAT+
- Fast Data Transfer: Achieve speeds of up to 450 Mbytes/s with the 4 Gbits/s PCIe 2.0 interface for NVMe SSDs and PCIe accessories.
- Seamless Compatibility: Fully compliant with HAT+ specification for easy integration with Raspberry Pi 5.
- Plug-and-Play: Automatically detected by the latest Raspberry Pi software and firmware.
- Easy Installation: Comes with a 16mm stacking header, spacers, and screws for convenient setup with the Active Cooler in place.
₹828.00 (Price is Exclusive of GST)Official Raspberry Pi M.2 HAT+
₹828.00 (Price is Exclusive of GST)3S 100A 12.6V Li-ion Lithium 18650 Battery BMS PCM Protection Board with Balance
- Charging voltage: 12.6V-13V
- Size: 70*60*8.5mm
- Over-discharge voltage range: 2.5±0.05v
- Upper limit working current: 100A (pay attention to heat dissipation)
- Working temperature: -40~+50°C
- Effective life: more than 30,000 hours
₹830.00 (Price is Exclusive of GST)3S 100A 12.6V Li-ion Lithium 18650 Battery BMS PCM Protection Board with Balance
₹830.00 (Price is Exclusive of GST)12V 3.5A 4000ml/min Liquid Diaphragm Pump
Features:
- Self-Priming
- Low Power Consumption
- Long Life
- Can Run in Dry Condition
₹835.00 (Price is Exclusive of GST)12V 3.5A 4000ml/min Liquid Diaphragm Pump
₹835.00 (Price is Exclusive of GST)SeeedStudio Grove GSR sensor
SeeedStudio
Features:
- Detects conductance of the skin
- Finger Straps for electrodes
₹840.00 (Price is Exclusive of GST)SeeedStudio Grove GSR sensor
₹840.00 (Price is Exclusive of GST)Arduino Mega 2560 R3 with USB Cable Compatible with Arduino
- Microcontroller: ATmega2560
- Operating Voltage: 5V
- Input Voltage (recommended): 7-12V
- Input Voltage (limits): 6-20V
- Digital I/O Pins: 54 (of which 15 provide PWM output)
- Analog Input Pins: 16
- DC Current per I/O Pin: 40 mA
- DC Current for 3.3V Pin: 50 mA
- Flash Memory: 256 KB of which 8 KB used by bootloader
- SRAM: 8 KB
- EEPROM: 4 KB
- Clock Speed: 16 MHz
- USB Host Chip: MAX3421E
- Length:101.98mm/4.01in
- Width:53.63mm/2.11in
- Height:15.29mm/0.60in
₹850.00₹1,475.00(Price is Exclusive of GST)Arduino Mega 2560 R3 with USB Cable Compatible with Arduino
₹850.00₹1,475.00(Price is Exclusive of GST)- ₹850.00 (Price is Exclusive of GST)
W5100 Network Expansion Board Ethernet Shield
₹850.00 (Price is Exclusive of GST) 3D Printer Filament – Multicolor PLA 1.75MM
- It is fed into the FDM 3D printer.
- It is extruded and deposited by an extrusion head onto a build platform where it cools.
- The process is continuous, building up layers to create the model.
₹850.00 (Price is Exclusive of GST)3D Printer Filament – Multicolor PLA 1.75MM
₹850.00 (Price is Exclusive of GST)Mini Sewing Machine – JYSM-202A
-Mini sewing machine offers double threads and perfect control of points
-Best view and more convenient in cutting the thread
-Small size, lightweight and with exquisite finish
-Equipped with a light lamp and a wire cutter, easy to cut the wires
-A large coil can be used with a rewind device for easy replacement of the bottom bobbin₹850.00₹950.00(Price is Exclusive of GST)Mini Sewing Machine – JYSM-202A
₹850.00₹950.00(Price is Exclusive of GST)BMS 24V 7S 20A Daly Waterproof BMS for Li-ion Cell (NMC) 25.9V
Features :
- Strong load ability, constant discharge current 10A~250A , use high voltage resistance, low inner resistance power Mosfet. The heat sink will greatly help cooling.
- IC itself has power balancing function. The circuit is simple and reliable.
- Typical voltage detection for each cell. So each battery will be prevented over charged or over discharged. Over current and short circuit protection function is very reliable. long time short circuit of the load won’t affect the PCB and the battery. Temperature protection during charging and discharging.
- Extreme low power consumption. the consumption of the whole device is less than 50uA.
- PCB use high anti-corrosion, high water resistance, high impedance ESD conformal coating.
₹850.00 (Price is Exclusive of GST)BMS 24V 7S 20A Daly Waterproof BMS for Li-ion Cell (NMC) 25.9V
₹850.00 (Price is Exclusive of GST)- ₹865.00 (Price is Exclusive of GST)
Sunflower kit in persuit of light (school science kit)
₹865.00 (Price is Exclusive of GST) 3D Pen Professional for 3D Printing Drawing Pen with 3 x 1.75mm ABS/PLA Filament
- The 3D printing pen has an ergonomic design that makes it comfortable for users.
- The 3D pen is a perfect gift for kids because it is safe and eco-friendly.
- The 3D pen for professionals is compatible with both 1.75mm ABS & PLA Filament.
- It features a Fast boot setup in just 30 seconds. You can draw and create quickly.
- This 3D printing pen is perfect for working professionals like architects, designers and model makers.
₹890.00 (Price is Exclusive of GST)3D Pen Professional for 3D Printing Drawing Pen with 3 x 1.75mm ABS/PLA Filament
₹890.00 (Price is Exclusive of GST)Sim900A GSM Modem Module
- Quad-band 850/900/1800/1900MHz.
- GPRS class 2/10.
- Input Voltage : 9V-12V DC.
- Control via AT commands (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT command set).
- Configurable baud rate.
- Built-in SIM Card holder.
- Built-in Network Status LED.
₹900.00 (Price is Exclusive of GST)Sim900A GSM Modem Module
₹900.00 (Price is Exclusive of GST)
