-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹638.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹638.00(Price is Exclusive of GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹264.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹264.00 (Price is Exclusive of GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST) -
ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (Price is Exclusive of GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (Price is Exclusive of GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹207.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹207.00 (Price is Exclusive of GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)
-
EL817 SMD-4 Transistor Output Optocoupler
- 10 to 20mA Collector current.
- 50mA Forward current.
- 6V Reverse voltage.
- 200mW Total power dissipation.
- Applications: Communications & Networking, Industrial.
₹8.00 (Price is Exclusive of GST)EL817 SMD-4 Transistor Output Optocoupler
₹8.00 (Price is Exclusive of GST) -
7805 Voltage Regulator IC
Features:
Fixed output voltage is 5V
Output current is 0.5A
Dropout voltage is 2V
Maximum DC input voltage is 35V
Output transition SOA protection
Output voltage tolerance is 4%
Operating temperature range 0C to 125C
Applications: Power Management.₹9.00 (Price is Exclusive of GST)7805 Voltage Regulator IC
₹9.00 (Price is Exclusive of GST) -
9v Battery Snap Connector with DC Jack
- Excellent material
- It is an environmental 9V battery buckle
- The Cable Length: 12cm Approx.
- Convenient for connecting a battery to your application.
- Save power and protect the environment
- Good electrical conductivity and comfortable sense of touch
₹9.00 (Price is Exclusive of GST)9v Battery Snap Connector with DC Jack
₹9.00 (Price is Exclusive of GST) -
DIP IC Socket Base Connector 28 Pin
- Type: DIP
- No of Pins: 28
₹9.00 (Price is Exclusive of GST)DIP IC Socket Base Connector 28 Pin
₹9.00 (Price is Exclusive of GST) -
LDR (Light Dependent Resistor) Sensor 5mm high quality
- Diameter: 5mm
- No. of Pins: 2
- Type of Mounting: PCB Through Hole
- Maximum Operating Temperature: +800°C (Approx.)
- Dark resistance:1-20 Mohm
₹9.00 (Price is Exclusive of GST)LDR (Light Dependent Resistor) Sensor 5mm high quality
₹9.00 (Price is Exclusive of GST) -
₹9.00 (Price is Exclusive of GST)Plastic Metal SPST 3 Pin 2 Way Toggle Switch 3A/5A AC 250V/125V
₹9.00 (Price is Exclusive of GST) -
Universal Heat Sink (25 x 25 x 10 mm)
- Quantity of blade: 8
- Material: Aluminum
- Color: Black
- Blade thickness: 1mm
- Base plate thickness: 2mm
- Dimensions: 25 x 25 x 10 mm
₹9.00 (Price is Exclusive of GST)Universal Heat Sink (25 x 25 x 10 mm)
₹9.00 (Price is Exclusive of GST) -
AMS1117-3.3V, 1A, SOT-223 Voltage Regulator IC
- Low dropout voltage
- Load regulation: 0.2% typical
- Optimized for Low Voltage
- On-chip thermal limiting
- Built-in thermal shutdown
- Good noise rejection
₹9.00 (Price is Exclusive of GST)AMS1117-3.3V, 1A, SOT-223 Voltage Regulator IC
₹9.00 (Price is Exclusive of GST) -
ALLIGATOR CLIP 4.5MM
The WD026 insulated alligator clips are perfect for use in electrical laboratory work. These small-sized alligator clips range in size from 35mm in length and are made from high-quality steel material. They come with an insulated coating to protect against accidental contact with live wires. These clips have a current rating of 5A and are available in various colors such as red, black, yellow, blue, green, and white. You can choose from three different lengths of 27.5 mm, 35 mm, and 42.5 mm depending on your requirements. These alligator clips come with crimp or solder termination options, making them versatile and easy to use in a variety of applications.
₹9.00 (Price is Exclusive of GST)ALLIGATOR CLIP 4.5MM
₹9.00 (Price is Exclusive of GST) -
PBT Connector Terminal Block 3 Pin
- 5.08mm pitch.
- Pin header: Tin plated brass.
- Contacts: Nickel plated brass.
- Strong, compact, lightweight.
- Heat resistant.
₹9.44 (Price is Exclusive of GST)PBT Connector Terminal Block 3 Pin
₹9.44 (Price is Exclusive of GST) -
650nm 6mm 5V DC 5mW Mini Laser Dot Diode Module
- Output Power: 5mW
- Working Voltage: 5V DC
- Working temperature: -10 ℃~＋40 ℃
- Housing material: Copper
- Working life: more than 2000 hours
- Spot mode: Dot Facula (continuous output)
- Laser wavelength: 650nm red-colored.
- Operating current: <40mA
- Power lead length: 120mm.
₹9.50 (Price is Exclusive of GST)650nm 6mm 5V DC 5mW Mini Laser Dot Diode Module
₹9.50 (Price is Exclusive of GST) -
Infrared IR Transmitter and Receiver (Photo-diode) Pair
Features:
- IR LED (TSFF5210)
- Package type: leaded
- Dimensions : 5mm
- Leads with stand-off
- Peak wavelength: λp = 870 nm
- High reliability
- High radiant power
- High radiant intensity
- Angle of half intensity: = ± 10°
- Low forward voltage
- Suitable for high pulse current operation
- High modulation bandwidth: fc = 24 MHz
- Good spectral matching with Si photodetectors
- IR Photodiode (BPV10NF)
- Package type: leaded
- Dimensions : 5mm
- Leads with stand-off
- Radiant sensitive area (in mm2): 0.78
- High radiant sensitivity
- Daylight blocking filter matched with 870 nm to 890 nm emitters
- High bandwidth: > 100 MHz at VR = 12 V
- Fast response times
- Angle of half sensitivity: ± 20°
₹10.00 (Price is Exclusive of GST)Infrared IR Transmitter and Receiver (Photo-diode) Pair
₹10.00 (Price is Exclusive of GST) - IR LED (TSFF5210)
