- “Pro-Range 3.7V 1000mAh 30C 1S Lithium Polymer Battery Pack” already exists in your wishlist
-
Alligator Clips10pcs of Double-ended Crocodile Clips Roach Clip
- Colour: Red, Green, Yellow, White, and Black, etc.
- Cable length: 45 cm.
- Net weight: 82 gm.
- They are very useful for connecting components to wires.
- It is insulation covered clips connected to the wire from both ends.
₹110.00 (Price is Exclusive of GST)Alligator Clips10pcs of Double-ended Crocodile Clips Roach Clip
₹110.00 (Price is Exclusive of GST) -
Ceramic Capacitor Kit 250pcs 25 value 1PF-0.1UF
- Good Quality item
- 25 values with 10pcs for each value
₹110.00 (Price is Exclusive of GST)Ceramic Capacitor Kit 250pcs 25 value 1PF-0.1UF
₹110.00 (Price is Exclusive of GST) -
TL082 JFET Input Operational Amplifier (Op-Amp) IC DIP-8 Package
TL082 JFET Input Operational Amplifier
- IC Name: TL082
- Package/Case: DIP-8
₹109.00 (Price is Exclusive of GST)TL082 JFET Input Operational Amplifier (Op-Amp) IC DIP-8 Package
₹109.00 (Price is Exclusive of GST) -
IR2110 High and Low Side Driver IC DIP-14 Package
IR2110 High and Low Side Driver
Features:-
- Floating channel designed for bootstrap operation Fully operational to +500V or +600V Tolerant to negative transient voltage dV/dt immune
- Gate drive supply range from 10 to 20V
- Undervoltage lockout for both channels
- 3.3V logic compatible Separate logic supply range from 3.3V to 20V Logic and power ground ±5V offset
- CMOS Schmitt-triggered inputs with pull-down
- Cycle by cycle edge-triggered shutdown logic
- Matched propagation delay for both channels
- Outputs in phase with inputs
₹108.00 (Price is Exclusive of GST)IR2110 High and Low Side Driver IC DIP-14 Package
₹108.00 (Price is Exclusive of GST) -
OV7670 640×480 VGA CMOS Camera Image Sensor Module
Specifications and Features:
- MODEL: OV7670 640X480 VGA CMOS CAMERA
- Pixel Coverage: 3.6um x 3.6um;
- Duck Current: 12 mV/s at 6’C
- Support VGA, CIF and from CIF to 40 x 30 format;
- Vario Pixel method for sub-sampling; Auto Image Control: AEC, AGC, AWB, ABF, ABLC;
- Image Quality Control: Color saturation, hue, gamma, sharpness, and anti-blooming;
- ISP includes noise reduction and defect correction; Support image scaling; Lens shading correction;
- Flicker 50/60Hz auto-detection;
- Color saturation level auto adjust;
- Edge enhancement level auto adjust;
- De-noise level auto adjust
- High sensitivity for low light applications
- Low voltage suitable for embedded applications
- Standard sccb interface, compatible with i2c interface
₹108.00 (Price is Exclusive of GST)OV7670 640×480 VGA CMOS Camera Image Sensor Module
₹108.00 (Price is Exclusive of GST) -
Solder Suction Tin Pump
- Metal body
- High suction power
- Teflon nozzle
- Easily replaceable nozzle
- Easy to clean and maintain
₹107.00 (Price is Exclusive of GST)Solder Suction Tin Pump
₹107.00 (Price is Exclusive of GST) -
28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver
- Rated voltage: 5V DC
- Reduction Ratio: 64:1
- Step Angle: 5.625° /64
- Frequency: 100Hz
- Self-positioning Torque: >34.3mN.m
- Friction torque: 600-1200 gf.cm
- Pull in torque: 300 gf.cm
₹107.00 (Price is Exclusive of GST)28BYJ-48 Stepper Motor and ULN2003 Stepper Motor Driver
₹107.00 (Price is Exclusive of GST) -
Power Adaptor Dual Pin 5 Volt 1 Amps
- Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz.
- Input current (mA): 100.
- Output Power: 5V 2A
- Load regulation (%): ±5.
- Input Plug: 2-Pin EU type.
- Output Plug: 2 in 1 dual DC Jack (5.5mm + 4mm).
₹106.00 (Price is Exclusive of GST)Power Adaptor Dual Pin 5 Volt 1 Amps
₹106.00 (Price is Exclusive of GST) -
Aluminum GT2 Timing Pulley 36 Tooth 8mm Bore For 6mm Belt
- Outer Diameter: 25.5 mm.
- Inner Diameter: 8 mm.
- Width: 17 mm.
- Weight: 14 gm.
- Material: Aluminum.
- No. of teeth: 36 on each side
₹105.00 (Price is Exclusive of GST)Aluminum GT2 Timing Pulley 36 Tooth 8mm Bore For 6mm Belt
₹105.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module
- 5V 4-Channel Relay interface board and each one needs 15-20mA Driver Current.
- Equipped with high-current relay, AC250V 10A; DC30V 10A.
- Standard interface that can be controlled directly by microcontroller (for Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Indication LED’s for Relay output status.
₹105.00 (Price is Exclusive of GST)4 Channel 5V Relay Module
₹105.00 (Price is Exclusive of GST) -
₹102.00 (Price is Exclusive of GST)
Yellow 0.28″ Mini 2 Wire Dc Voltmeter 0.2-100v Digital Display Voltmeter Gauge LED Voltage
₹102.00 (Price is Exclusive of GST) -
CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
Features :
- Coolant enable
- Uses removable Pololu A4988 compatible stepper drivers. (A4988, DRV8825 and others) (Not Included)
- Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
- Compact design.
- Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
- Runs on 12-36V DC. (At the moment only the Pololu DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
- Please note that this is an unassembled kit and needs soldering.
- Latest Arduino CNC Shield Version 3.10
- GRBL 0.9 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
- PWM Spindle and direction pins
- 4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
- 2 x End stops for each axis (6 in total)
₹100.00 (Price is Exclusive of GST)CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board
₹100.00 (Price is Exclusive of GST)
