No products in the cart.
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (Price is Exclusive of GST)
I2C Bi-Directional Logic Level Converter- 4 Channel
- Mutual transform between 5V TTL and 3.3V TTL
- Four channels of logic and high voltage low voltage logic can two-way transform
- Portable and lightness, with 2 rows 6 pin contact pins
- Level Converter- 4 Channel Compatible with the bread plate, can be used directly put on the breadboard
- 4 Channel Module (great for I2C or SPI) and will work with all microcontrollers, Arduino, Raspberry Pi, Intel Edison, NXP Mbed
₹46.00 (Price is Exclusive of GST)I2C Bi-Directional Logic Level Converter- 4 Channel
₹46.00 (Price is Exclusive of GST)Infrared IR Wireless Remote Control Module Kit for Arduino
Features :
- Depending on the surrounding environment and the sensitivity of the receiver the transmission distance may be affected.
- Photo-detector and preamplifier in one package.
- Internal filter for PCM frequency.
- Improved shielding against EMI.
₹45.00 (Price is Exclusive of GST)Infrared IR Wireless Remote Control Module Kit for Arduino
₹45.00 (Price is Exclusive of GST)GL-12 840 Hole Solderless Breadboard
- Product model: GL-12
- Product pitch: 840 holes
- Excellent quality breadboard.
- ABS plastic material.
- Reusable for fast build a prototype of an electronic circuit
₹45.00₹65.00(Price is Exclusive of GST)GL-12 840 Hole Solderless Breadboard
₹45.00₹65.00(Price is Exclusive of GST)L293D Motor Driver Board
- The driver two holes of 3 mm dia.
- Male burg-stick connectors for supply, ground and input connection.
- Screw terminal connectors for easy motor connection.
- High noise immunity inputs.
₹45.00 (Price is Exclusive of GST)L293D Motor Driver Board
₹45.00 (Price is Exclusive of GST)8X8 Mini Dot Matrix LED Display
- Easy to Install on Breadboard
- Bright LED lights
- Compact Design.
- LED Size: 3mm
- Configuration: Common Cathode
₹45.00 (Price is Exclusive of GST)8X8 Mini Dot Matrix LED Display
₹45.00 (Price is Exclusive of GST)Jumper Wire Male to Male 20 cm (Set of 40 Piece)
40 pc male to male
- Each cable length about 20cm or 8-inch
- The male ends meant for insertion into standard 0.1 inch (2.54mm) female sockets and the female ends are meant for insertion onto standard 0.1 inch (2.54mm) male headers
- Suitable for Arduino breadboard kit project, PCB project, pc motherboard, etc
- Through the pin connection, without welding, fit for fast circuit test.
₹45.00₹60.00(Price is Exclusive of GST)Jumper Wire Male to Male 20 cm (Set of 40 Piece)
₹45.00₹60.00(Price is Exclusive of GST)- ₹45.00
₹60.00(Price is Exclusive of GST)Jumper Wire Male to Female 20 cm (Set of 40 Piece)
₹45.00₹60.00(Price is Exclusive of GST) Jumper Wire Female to Female 20 cm (Set of 40 Piece)
Features :
Compatible with 2.54mm spacing pin headers
40pcs chromatic color jump wire
High quality and in good working condition
Durable and reusable
Easy to install and use
A popular choice for construction or repair
Be used for the electronic project and Genuine Arduino product
Flexible Breadboard Jumper Cable Wire allows you to plug and unplug easily for prototyping.
₹45.00₹60.00(Price is Exclusive of GST)Jumper Wire Female to Female 20 cm (Set of 40 Piece)
₹45.00₹60.00(Price is Exclusive of GST)SW-420 Vibration Sensor Module
- Using SW-420 normally closed type vibration sensor.
- Comparator output, clean signal, good waveform, strong driving ability, >15mA.
- Using a wide voltage LM393 comparator.
- With bolt holes for easy installation.
₹45.00 (Price is Exclusive of GST)SW-420 Vibration Sensor Module
₹45.00 (Price is Exclusive of GST)DHT11 Temperature and Humidity Sensor Module
- DHT11 sensor with PCB and LED indicator; 3 to 5V power and I/O, 4 pins with 0.1″ spacing
- The board has pre-built 4.7K or 10K resistor, which you will need to use as a pull-up from the data pin to VCC.
- 2.5mA max current use during conversion (while requesting data)
- Good for 20-80% humidity readings with 5% accuracy
- Good for 0-50°C temperature readings ±2°C accuracy.
₹45.00₹92.00(Price is Exclusive of GST)DHT11 Temperature and Humidity Sensor Module
₹45.00₹92.00(Price is Exclusive of GST)Multicolor Flat Ribbon Cable, 20 Wire per 1 meter
Features :
- Easily and directly inserted into PCB.
- Suitable for internal wiring in office equipment, audio, and video machines.
- Durable and reusable.
- Easy to install and use.
- A popular choice for construction or repair.
- Useful for the electronic project and Genuine Arduino product.
₹44.00₹55.00(Price is Exclusive of GST)Multicolor Flat Ribbon Cable, 20 Wire per 1 meter
₹44.00₹55.00(Price is Exclusive of GST)GT2 Close-Loop Rubber Timing Belt for 3D Printer
GT2 Close-Loop Rubber Timing Belt
- Pitch: 2mm
- Material: Neoprene Rubber With Fiberglass Core
- Width: 6mm
- Total Length: 188mm
- Belt Height: 1.52 mm
- Tooth Height: 0.76mm
- Shape: Closed Loop
₹43.00 (Price is Exclusive of GST)GT2 Close-Loop Rubber Timing Belt for 3D Printer
₹43.00 (Price is Exclusive of GST)
