No products in the cart.
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹390.00 (Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (Price is Exclusive of GST)
ORANGE 6mm Light Push Button Switch Kit-100PCS
Features:
- Through-hole design.
- Shaft Shape: Round
- Used in the fields of electronic products, household appliances, and more.
- High precision mechanism design offers acute operation and long service life.
- Compact and lightweight, easy to carry and dismantle.
- Good electrical conductivity.
₹370.00 (Price is Exclusive of GST)ORANGE 6mm Light Push Button Switch Kit-100PCS
₹370.00 (Price is Exclusive of GST)Mega2560 R3 RAMPS 3D Printer Controller Board (1.4 MKS Gen L V1.0)
Pin Diagram:
Features:
1. Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware
2. Firmware can have the same configuration as ramps1.4
3. Easy DISPLAY + SD-CARD connector, RepRapDiscount SmartController compatible pin header on board
4. Easy connect MKS TFT to AUX-1
5.3x temperature ADC connectors for thermistors
6.up 5 motor driver with A4982
7.4x PWM enable mosfet outputs voltage selector switch for Main Power. (Bed, Extruder0, Extruder1, Fans)
8.4 layers PCB, optimize heat dissipation.
9.6x end stop connectors with power supply Xmin / Xmax / Ymin / Ymax / Zmin / Zmax
10. Resettable fuse for short circuit.
₹2,022.00 (Price is Exclusive of GST)Mega2560 R3 RAMPS 3D Printer Controller Board (1.4 MKS Gen L V1.0)
₹2,022.00 (Price is Exclusive of GST)ESP WROOM 32 MCU Module Version: 1.1
The user may also power off the CPU and make use of the low-power coprocessor to constantly monitor the peripherals for changes or crossing of thresholds. ESP32S integrates a rich set of peripherals, ranging from capacitive touch sensors, Hall sensors, low-noise sense amplifiers, SD card interface, Ethernet, high-speed SDIO/SPI, UART, and I²C.
Application :
- Universal low power IoT sensor hub.
- Home automation.
- Universal low power IoT recorder.
- Mesh network.
- Video streaming of the camera.
- Industrial wireless control.
- OTT TV box / set-top box device.
- Baby monitor.
- Smart Socket.
- Sensor networks.
- Wi-Fi toys: Counters, toys, Anti-lost device.
- Wearable electronic products.
- Wi-Fi speech recognition device.
- Wi-Fi location-aware devices.
Features :
- Integrated 520 KB SRAM.
- Hybrid Wi-Fi & Bluetooth.
- High level of integration.
- Ultra-low-power management.
- 4 MB Flash.
- On-board PCB antenna.
₹410.00 (Price is Exclusive of GST)ESP WROOM 32 MCU Module Version: 1.1
₹410.00 (Price is Exclusive of GST)STM32F401CCU6 Minimum System Board Microcomputer STM32 ARM Core Board
Features :
- 100% Brand new and high-quality STM32 Board
- 84 MHz work frequency.
- 256K flash memory,64K SRAM.
- 1.7-3.6V power, I/O.
- 4-26MHz crystal.
- Onboard the Type-C USB interface, you can give the board power supply and USB communication.
₹410.00 (Price is Exclusive of GST)STM32F401CCU6 Minimum System Board Microcomputer STM32 ARM Core Board
₹410.00 (Price is Exclusive of GST)- ₹4,573.00 (Price is Exclusive of GST)
TL866II Plus Universal Programmer Kit with 6 IC Adapters
₹4,573.00 (Price is Exclusive of GST) NEEMA 17-JK42HM48-1684-0.44N-m Round Type
Features :
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
₹1,010.00 (Price is Exclusive of GST)NEEMA 17-JK42HM48-1684-0.44N-m Round Type
₹1,010.00 (Price is Exclusive of GST)Lemon Lithium Polymer Battery Pack 3300mAh 3S 25C/50C
Features:
- Guaranteed leak proof operation in any position except inverted
- The expected life span of two to three years in float service applications
- Operation in a broad range of ambient temperatures
- Recovery capabilities even after deep discharges
- Compact, quick and simple to install, require low maintenance
₹2,870.00 (Price is Exclusive of GST)Lemon Lithium Polymer Battery Pack 3300mAh 3S 25C/50C
₹2,870.00 (Price is Exclusive of GST)NEEMA 23-JK57HS112-4204-3.1N-m Round Type
Note :
- The Neema 23 3.1N-m Stepper motor dimensions and weight may have a ±2% error.
- Resonances can occur because of improper mounting.
- Not easy to operate at extremely high speeds.
Features :
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
₹2,365.00 (Price is Exclusive of GST)NEEMA 23-JK57HS112-4204-3.1N-m Round Type
₹2,365.00 (Price is Exclusive of GST)Lemon Lithium Polymer Battery Pack 1800mAh 3S 75C/150C
Features:
- Guaranteed leak proof operation in any position except inverted
- The expected life span of two to three years in float service applications
- Operation in a broad range of ambient temperatures
- Recovery capabilities even after deep discharges
- Compact, quick and simple to install, require low maintenance
₹2,025.00 (Price is Exclusive of GST)Lemon Lithium Polymer Battery Pack 1800mAh 3S 75C/150C
₹2,025.00 (Price is Exclusive of GST)Creality Ender 3 V2 3D Printer
It’s the same old Ender-3 3D Printer experience, improved with current hardware that includes a 32-bit mainboard, silent stepper motor drivers, a much cleaner appearance and design, plus plenty of other, smaller, touches.
Features:
- Integrated Compact Design
- Multiple improved upgrades
- Ultra silent printing
₹17,170.00 (Price is Exclusive of GST)Creality Ender 3 V2 3D Printer
₹17,170.00 (Price is Exclusive of GST)NEEMA 17-JK42HS34-0406-0.15N-m Round Type 1.5 Kg
Note :
- The Nema17 0.15N-m Stepper motor dimensions and weight may have a ±2% error.
- Resonances can occur because of improper mounting.
- Not easy to operate at extremely high speeds.
Features :
- The input pulse decides the rotation angle of the motor.
- High accuracy of around 3 to 5% a step.
- It provides good starting, stopping, and reversing.
- Control of this motor is less costly because of the exclusion of complex control circuitry.
- The speed is proportional to the frequency of the input pulses.
₹599.00 (Price is Exclusive of GST)NEEMA 17-JK42HS34-0406-0.15N-m Round Type 1.5 Kg
₹599.00 (Price is Exclusive of GST)MT30 3 Pole Motor/ESC Connector Set Female-1Pcs
Features:
- Brand: Amass
- Suitable for: 16AWG wire (Max)
- Color: Yellow
- Gender: Female
- Gold Plated Connector
- High-Quality Material
₹75.00 (Price is Exclusive of GST)MT30 3 Pole Motor/ESC Connector Set Female-1Pcs
₹75.00 (Price is Exclusive of GST)
