No products in the cart.
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST)Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹750.00 (excl. GST)Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
₹750.00 (excl. GST)Waveshare 7inch Capacitive Touch Screen LCD (B)
Features:
- 800×480 High-Resolution Display
- Capacitive Touch Control
- HDMI Interface for Display, USB Interface for Touch Control
- Supports Raspberry Pi, comes with Raspbian driver (Works directly with Raspbian), and Ubuntu Image
- Supports Banan Pi, Banana Pro, comes with LUbuntu, Raspbian Image
- Supports BB Black, comes with Angstrom Image
- Not only SBC’s, but it can also work with any computer display with HDMI Interface, Touch interface will not work in that case.
- Backlight control, for lower power consumption.
₹4,200.00₹4,600.00(excl. GST)Waveshare 7inch Capacitive Touch Screen LCD (B)
₹4,200.00₹4,600.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (excl. GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (excl. GST)Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (excl. GST)Capacitive Soil Sensor V2.0
₹60.00 (excl. GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (excl. GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (excl. GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (excl. GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (excl. GST)
- “Dual Channel Digital Power Board XH-M543, DC12-26V 2x120W DIY Module High Power Stereo Amp Board for Car Vehicle Computer Speaker DIY Home Theater Audio System” already exists in your wishlist
Two Wheel Drive (2WD Kit) Smart Robot Bot with Chassis, Bo Motor, Wheels -DIY Robot Chassis
- Mechanical structure is simple, it is easy to install
- Package included :- 1 x car chassis, 2 x gear motor(1:48), 2 x wheel and all necessary screw and nut
- Wheel size: 6.6cm x 2.6cm approx
- Wheel center hole: 5.3mm long, 3.5mm wide
₹300.00 (excl. GST)Ublox NEO 6M GPS module
- 5Hz position update rate.
- The cold start time of 38 s and Hot start time of 1 s.
- Configurable from 4800 Baud to 115200 Baud rates. (default 9600).
- SuperSense ® Indoor GPS: -162 dBm tracking sensitivity.
- Support SBAS (WAAS, EGNOS, MSAS, GAGAN).
- Separated 18 x 18mm GPS antenna.
₹335.00₹490.00(excl. GST)Ublox NEO 6M GPS module
₹335.00₹490.00(excl. GST)ULN2003 Stepper Motor Driver IC
- 500-mA-Rated Collector Current (Single Output)
- High-Voltage Outputs: 50 V
- Output Clamp Diodes
- Inputs Compatible With Various Types of Logic
- Relay-Driver Applications
₹15.00 (excl. GST)ULN2003 Stepper Motor Driver IC
₹15.00 (excl. GST)ULN2003A Driver Module Stepper Motor Driver Board
- ULN2003A motor driver chip
- Chip all the pins already leads for easy connection to use
- 5-12V power supply
- 4-way signal indicator
- Step angle: 5.625 x 1 / 64
- Reduction ratio: 1 / 64
- Phase: 4
- Current / Phase: 5V
₹41.00 (excl. GST)ULN2003A Driver Module Stepper Motor Driver Board
₹41.00 (excl. GST)Universal Aluminium Heat Sink 11 x 11 x 5 mm – 5Pcs.
Features:
- Prevents overheating of board
- Absorbs heat quickly
- Fast cooling
- Quantity of blade: 4
- Material: Aluminum
- Color: Silver
₹23.76₹35.00(excl. GST)Universal Aluminium Heat Sink 11 x 11 x 5 mm – 5Pcs.
₹23.76₹35.00(excl. GST)Universal Heat Sink (25 x 25 x 10 mm)
- Quantity of blade: 8
- Material: Aluminum
- Color: Black
- Blade thickness: 1mm
- Base plate thickness: 2mm
- Dimensions: 25 x 25 x 10 mm
₹9.00 (excl. GST)Universal Heat Sink (25 x 25 x 10 mm)
₹9.00 (excl. GST)Universal Swivel Casters Wheel
Features:
Wheel Type : White Nylon, Dual roller bearing
Load bearing: 10kg
Hole diameter: 4mm
Material: White Nylon PP Material And Steel₹30.00 (excl. GST)Universal Swivel Casters Wheel
₹30.00 (excl. GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(excl. GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(excl. GST)UNO SMD Atmega328P Development Board compatible with Arduino
Features-
- Flash Memory – 32 KB (ATmega32u4) of which 4 KB used by boot loader
- SRAM – 2 KB (ATmega328P)
- EEPROM – 1 KB (ATmega328P)
₹190.00₹550.00(excl. GST)UNO SMD Atmega328P Development Board compatible with Arduino
₹190.00₹550.00(excl. GST)Unsoldered GY-2561 TSL2561 Luminosity Sensor Light Intensity Module
1.Model: TSL2561
2.I2C interfaces
3.Power supply:3.3v to 5v
4.low supply current max: 0.6mA
₹285.00 (excl. GST)Unsoldered GY-2561 TSL2561 Luminosity Sensor Light Intensity Module
₹285.00 (excl. GST)USB 2.0 Cable Type A/B for Arduino UNO
- Fully compatible with the PC.
- Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
- Aluminum under mold shield helps meet FCC requirements on KMI/RFI interference.
- Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
₹18.00 (excl. GST)USB 2.0 Cable Type A/B for Arduino UNO
₹18.00 (excl. GST)- ₹85.00 (excl. GST)
USB to TTL Serial Converter Adapter Cable
₹85.00 (excl. GST)
