NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹390.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹390.00 (Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
- Voltage: 12V to 24V; Max Current: 25A
- Can work stably when the current is not more than 25A
- Maximum power of the heated bed: Over 300W (12V) or 600W (24V) Make sure that the cables that connect to the controller board and hotbed can withstand high current
₹200.00 (Price is Exclusive of GST)Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
₹200.00 (Price is Exclusive of GST)
₹1,850.00 (Price is Exclusive of GST)MAXX PAMMA 936 Temperature Controlled Soldering Station ESD Safe 60 W Temperature Controlled (Round Tip)
₹1,850.00 (Price is Exclusive of GST)Readytosky 80A ESC 2-6S Brushless ESC Speed Controller for RC Drone
Features:
- Security power function: When the power is turned on, regardless of the throttle stick at any position will not start the motor immediately to prevent personal injury
- Throttle range calibrated function: to adapt the throttle differences between different strokes, improve the linearity of throttle response
- programmed project (available throttle stick or card LED parameter settings):
- Brake setting: No brake / with brake
- Battery Type: Lithium battery / NiMH
- Low Voltage Protection Mode: Soft Shutdown / hard off
- Low Voltage Protection Threshold: low / medium / high
- start mode: Normal / Soft / Super-soft and start
- Timing: low / medium / high
- Restore factory defaults
- Comprehensive protection features:
- Under-voltage protection: the program set by the user when the battery voltage is below the protection threshold, ESC automatically reduces the output power
- Overvoltage Protection: input voltage exceeds the input range are not allowed to start, automatic protection, also issued a hasty “beep” Warning
- Overheat protection: built-in temperature detection circuit that automatically reduces the output power ESC temperature is too high
- Remote signal loss protection: remote control signal is lost for 1 second to reduce the power, and then have two seconds to turn off without the remote control signal output
₹1,866.00 (Price is Exclusive of GST)Readytosky 80A ESC 2-6S Brushless ESC Speed Controller for RC Drone
₹1,866.00 (Price is Exclusive of GST)Full Set DIY 2DOF Robot Arm Manipulator Claw+2pcs Servo Brackets(Not Assembly) Kit
Specifications and Features :
- Aluminum Matte Coat Pan and Tilt for the horizontal surface, unassembled
- Servo bracket used in the shoulders and knees or another joint of humanoid robots, biped robots etc.
- Can plant a camera or IR sensor for Robot.
- Package total weight: 112 gm
- Clamp Claw:
- Weight capacity is about 300 gm objects
- Material: Full aluminum alloy
- Weight: About 64gm
- Maximum angle: 54mm
- Total length: 110mm (paw when closed overall longest length)
- Total width: 94mm (the claws open when the maximum overall width)
- Compatible with our MG995 Servo
₹1,887.60 (Price is Exclusive of GST)Full Set DIY 2DOF Robot Arm Manipulator Claw+2pcs Servo Brackets(Not Assembly) Kit
₹1,887.60 (Price is Exclusive of GST)Arduino UNO R4 Minima board
Features:
- 32-bit development board, being previously based on 8-bit AVR
- The board features the standard 14 digital I/O ports, 6 analog channels
- dedicated pins for I²C, SPI and UART connections.
- Larger memory:
- 8 times more flash memory (256 kB)
- 16 times more SRAM (32 kB).
- Easy power management:
- The UNO R4 has a barrel jack connector and supports input voltages from 6-24 V.
- This connector is widely popular and removes the need for additional circuitry required to step down the voltage.
- Cross compatibility:
- The UNO form factor automatically makes it compatible with hundreds of existing third-party shields
and other accessories.
- The UNO form factor automatically makes it compatible with hundreds of existing third-party shields
₹1,900.00 (Price is Exclusive of GST)Arduino UNO R4 Minima board
₹1,900.00 (Price is Exclusive of GST)Orange Lithium Polymer Battery Pack 4200mAh 2S 35C/70C (7.4V)
Features :
- Product Type: Lithium Polymer Battery Pack
- The Orange LiPo battery has matched resistance.
- Good Temperature Control.
- Minimum weight in Class
Precautions :
- Avoid over-charging or over-discharge batteries
- Do not put it besides the high-temperature condition
- Don’t directly expose it into the fire
- Avoid the contact of water.
- Do not Short Circuit the battery Terminals
₹1,940.00 (Price is Exclusive of GST)Orange Lithium Polymer Battery Pack 4200mAh 2S 35C/70C (7.4V)
₹1,940.00 (Price is Exclusive of GST)600VA/360Watt Uninterrupted Power Supply -UPS FPS-755
- Compact Design Line Interactive UPS with Load Capacity of 360Watts / 600VA. Output Frequency (sync to mains) : 47 – 63 Hz Sync to mains
- Three Battery Backed up and Surge Protected 6A, 2/3 Pin Output Indian Power Socket
₹2,000.00 (Price is Exclusive of GST)600VA/360Watt Uninterrupted Power Supply -UPS FPS-755
₹2,000.00 (Price is Exclusive of GST)LX-103 Light Meter Luxmeter, Measures Up-To 2,00,000 LUX/20,000 FC
Features Of HTC LX-103 Digital Lux Meter:
- Large Range up to 200000Lux
- Large LCD Display with Back Light and Bar Graph
- Auto Power Off
- MAX/MIN and Data Hold
₹2,015.00 (Price is Exclusive of GST)LX-103 Light Meter Luxmeter, Measures Up-To 2,00,000 LUX/20,000 FC
₹2,015.00 (Price is Exclusive of GST)Mega2560 R3 RAMPS 3D Printer Controller Board (1.4 MKS Gen L V1.0)
Pin Diagram:
Features:
1. Arduino MEGA compatible Atmega2560 and FT232 processors are compatible with all RAMPS class firmware
2. Firmware can have the same configuration as ramps1.4
3. Easy DISPLAY + SD-CARD connector, RepRapDiscount SmartController compatible pin header on board
4. Easy connect MKS TFT to AUX-1
5.3x temperature ADC connectors for thermistors
6.up 5 motor driver with A4982
7.4x PWM enable mosfet outputs voltage selector switch for Main Power. (Bed, Extruder0, Extruder1, Fans)
8.4 layers PCB, optimize heat dissipation.
9.6x end stop connectors with power supply Xmin / Xmax / Ymin / Ymax / Zmin / Zmax
10. Resettable fuse for short circuit.
₹2,022.00 (Price is Exclusive of GST)Mega2560 R3 RAMPS 3D Printer Controller Board (1.4 MKS Gen L V1.0)
₹2,022.00 (Price is Exclusive of GST)Lemon Lithium Polymer Battery Pack 1800mAh 3S 75C/150C
Features:
- Guaranteed leak proof operation in any position except inverted
- The expected life span of two to three years in float service applications
- Operation in a broad range of ambient temperatures
- Recovery capabilities even after deep discharges
- Compact, quick and simple to install, require low maintenance
₹2,025.00 (Price is Exclusive of GST)Lemon Lithium Polymer Battery Pack 1800mAh 3S 75C/150C
₹2,025.00 (Price is Exclusive of GST)Pro-Range INR 18650 P28A 7.4V 5600mAh 2S2P 60A/70A Discharge Li-ion Drone Battery Pack
- Nominal Capacity (mAh): 5600
- Nominal Voltage (v): 7.4
- Max Charging Voltage (v): 8.4
- Charge Port: 3 Pin JST XH
- Discharge Port: Amass XT60
₹2,054.00 (Price is Exclusive of GST)Pro-Range INR 18650 P28A 7.4V 5600mAh 2S2P 60A/70A Discharge Li-ion Drone Battery Pack
₹2,054.00 (Price is Exclusive of GST)Pro-Range INR 18650 P28A 14.8V 2800mAh 4S1P 30A/35A Discharge Li-ion Drone Battery Pack
- Nominal Capacity (mAh): 2800
- Nominal Voltage (v): 14.8
- Max Charging Voltage (v): 16.8
- Charge Port: 5 Pin JST XH
- Discharge Port: Amass XT60
₹2,054.00 (Price is Exclusive of GST)Pro-Range INR 18650 P28A 14.8V 2800mAh 4S1P 30A/35A Discharge Li-ion Drone Battery Pack
₹2,054.00 (Price is Exclusive of GST)Pro-Range INR 18650 P28A 14.8V 2800mAh 4S1P 30A/35A Discharge Li-ion Drone Battery Pack with XT30
- Nominal Capacity (mAh): 2800
- Nominal Voltage (v): 14.8
- Max Charging Voltage (v): 16.8
- Charge Port: 5 Pin JST XH
- Discharge Port: Amass XT60
₹2,054.00 (Price is Exclusive of GST)Pro-Range INR 18650 P28A 14.8V 2800mAh 4S1P 30A/35A Discharge Li-ion Drone Battery Pack with XT30
₹2,054.00 (Price is Exclusive of GST)
