-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹638.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹638.00(Price is Exclusive of GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹264.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹264.00 (Price is Exclusive of GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST) -
ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (Price is Exclusive of GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (Price is Exclusive of GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹207.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹207.00 (Price is Exclusive of GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)
-
₹80.00 (Price is Exclusive of GST)ACS712 Test Current Sensor Module 20A
₹80.00 (Price is Exclusive of GST) -
BMS 4 Series 14.8V 18650 Lithium Battery Equalization Board
- Type:Â Voltage Regulator
- Supply Voltage:14.8V/16.8V
- Dissipation Power:18650 Lithium Battery Balanced Function Board
- Operating Temperature:Â Discharge Shunt balanced 4.2V 66mA
₹79.00 (Price is Exclusive of GST)BMS 4 Series 14.8V 18650 Lithium Battery Equalization Board
₹79.00 (Price is Exclusive of GST) -
DHT11 Digital Temperature And Humidity Sensor
The DHT-11 has a temperature measurement range of 0°C to 50°C with an accuracy of ±2°C
a humidity measurement range of 20% to 80% RH with an accuracy of ±5% RH.
the DHT-11 is an excellent choice for any electronics project that requires temperature and humidity sensing.
₹78.00 (Price is Exclusive of GST)DHT11 Digital Temperature And Humidity Sensor
₹78.00 (Price is Exclusive of GST) -
₹78.00 (Price is Exclusive of GST)L9110S H Bridge Stepper Motor Dual DC Driver Controller Module
₹78.00 (Price is Exclusive of GST) -
ADC0809CCN-IC ADC 8BIT SAR 28DIP
ADC0809CCN
Reference Type :External
Voltage – Supply, Analog : 4.5V ~ 6.5V
Voltage – Supply, Digital : 4.5V ~ 6.5V
Features
-Operating Temperature : -40°C ~ 85°C
Package / Case : 28-DIP (0.600″, 15.24mm)
Supplier Device Package : 28-DIP
Mounting Type : Through Hole
₹75.00 (Price is Exclusive of GST)ADC0809CCN-IC ADC 8BIT SAR 28DIP
₹75.00 (Price is Exclusive of GST) -
DRV8825 Stepper Motor Driver with Aluminum Heat Sink
Features :
- Microstep resolutions:Â full, 1/2, 1/4, 1/8, 1/16, and 1/32.
- Simple step and direction control interface
- Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
- Adjustable current control lets you set the maximum current output with a potentiometer. Hence lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
- Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
- 45Â V maximum supply voltage
- Built-in regulator (no external logic voltage supply needed)
- Can interface directly with 3.3Â V and 5Â V systems
- Over-temperature thermal shutdown, over-current shutdown, and under-voltage lockout
- Short-to-ground and shorted-load protection
- 4-layer, 2Â oz copper PCB for improved heat dissipation
- Exposed solderable ground pad below the driver IC on the bottom of the PCB
₹75.00 (Price is Exclusive of GST)DRV8825 Stepper Motor Driver with Aluminum Heat Sink
₹75.00 (Price is Exclusive of GST) -
HT12D and HT12E Encoder Decoder IC
Feature:
- Operating voltage: 2. 4V~12v
- Easy interface with an rf or an infrared transmission medium
- Minimal external components
- 18 Pin IC
₹75.00 (Price is Exclusive of GST)HT12D and HT12E Encoder Decoder IC
₹75.00 (Price is Exclusive of GST) -
W1209 Digital Temperature Controller Switch Thermostat
- Temperature Control Range(°C): -50 to +110
- Resolution @-9.9°C to +99.9°C: 0.1°C
- Resolution @all temperatures: 1°C
- Accuracy: 0.1°C
- Refresh Rate(s): 0.5
- Supply Voltage(V): 12
- Measuring Inputs: NTC10K
- Cable Length: 0.5 Meter
- Output Type: 1 Channel Relay Output
- Capacity: 10A
₹75.00 (Price is Exclusive of GST)W1209 Digital Temperature Controller Switch Thermostat
₹75.00 (Price is Exclusive of GST) -
18650 Battery Holder Case DIY Lithium Battery Box Battery Holder with Pin for 4 * 18650
- Size: As shown in images, suitable for 18650 lithium ion battery, Four Cell holder
- Color: Black; 1pcs 18650 Battery Holder Case Leads 3.7V Clip Type for Soldering / Connecting
- Material Type: Metal and plastic
- The package does not include battery of any type, only the cover.
₹72.00 (Price is Exclusive of GST)18650 Battery Holder Case DIY Lithium Battery Box Battery Holder with Pin for 4 * 18650
₹72.00 (Price is Exclusive of GST) -
2400-2500 MHz 3dBi 3G/4G LTE PCB Antenna
Application: 2G, 3G, 4G LTE, ISM
Features:
- Compact Size
- High quality
- Low cost
- 3M high-quality adhesive
- Masking for corrosion-free
₹71.30 (Price is Exclusive of GST)2400-2500 MHz 3dBi 3G/4G LTE PCB Antenna
₹71.30 (Price is Exclusive of GST) -
AC Voltage Sensor Module ZMPT101B (Single Phase)
- Voltage – 250V
- Easy PCB mounting
- Good consistency
- Widely acclaimed
₹71.00 (Price is Exclusive of GST)AC Voltage Sensor Module ZMPT101B (Single Phase)
₹71.00 (Price is Exclusive of GST) -
AT89S52-24PU DIP-40 Microcontroller
- Package/Case: DIP-40
- 8K Bytes of In-System Reprogrammable Flash Memory
- Endurance: 1,000 Write/Erase Cycles
- Fully Static Operation: 0 Hz to 33 MHz
- Three-level Program Memory Lock
- 256 x 8-Bit Internal RAM
- 32 Programmable I/O Lines
- Three 16-bit Timer/Counters
- Eight Interrupt Sources
- Programmable Serial Channel
- Low Power Idle and Power Down Modes
₹71.00 (Price is Exclusive of GST)AT89S52-24PU DIP-40 Microcontroller
₹71.00 (Price is Exclusive of GST)
