-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹638.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹638.00(Price is Exclusive of GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹264.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹264.00 (Price is Exclusive of GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC:Â 3.3V-5V
GND:Â GND
DO:Â Digital output interface(0 and 1)
AO:Â Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST) -
ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (Price is Exclusive of GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (Price is Exclusive of GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹207.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹207.00 (Price is Exclusive of GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)
-
NRF24L01 Wireless Transceiver Module-2.4GHz
The embedded baseband protocol engine (Enhanced ShockBurst) is based on packet communication and supports various modes from manual operation to advanced autonomous protocol operation.
Features :
- Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability,
- Particularly suitable for industrial control applications.
- 125 Channels, Multi-point communication, and frequency hopping to meet the communication needs
- Built-in hardware CRC error detection, Multipoint communication address control.
- Low-power 1.9 ~ 3.6V, only 1uA on Power down mode
- Built-in 2.4Ghz antenna
- Available software to set the address only received local Address when output data(Provide interrupt instruction), can be directly connected to a variety of microcontrollers, Software programming is very convenient.
- Built-in voltage regulator
- Standard DIP Pitch Interface for embedded applications.
₹65.00 (Price is Exclusive of GST)NRF24L01 Wireless Transceiver Module-2.4GHz
₹65.00 (Price is Exclusive of GST) -
Desoldering Pump Tool
- One-handed solder sucker with powerful suction whether you are right or left-handed, you can using the desoldering pump by just cocking it and pressing the trigger button with one hand when you are ready, the desoldering pump designed with double ring double open and “vacuum” button, which make the sucking power awesome
₹65.00 (Price is Exclusive of GST)Desoldering Pump Tool
₹65.00 (Price is Exclusive of GST) -
DC PWM Motor Speed Controller
- The maximum output power:30W
- Input supply voltage:1.8V-15VDC
- The Maximum continuous output current:2A
- Duty Cycle adjustable:0%-100%
₹65.00 (Price is Exclusive of GST)DC PWM Motor Speed Controller
₹65.00 (Price is Exclusive of GST) -
2 Channel 12V Relay Module with Optocoupler
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 (Price is Exclusive of GST)2 Channel 12V Relay Module with Optocoupler
₹65.00 (Price is Exclusive of GST) -
2 Channel 5V Relay Module
- Low Level Trigger Relay Module
- Two separate LEDs for On/Off indication of the Relay.
- Triggering input voltage 3.3V – 5V
- Two separate LEDs for On/Off indication of the Relay
- Triggering input voltage 3.3V – 5V 4)
- Back EMF protection
- Back EMF protection 2 LEDs to indicate when relays are ON.
- Works with logic level signals from 3.3V or 5V devices
- Opto isolation circuitry
- Module with diode current protection, short response time
- AC Control Voltage: 250V @max.10A
- DC Control Voltage: 30V @max. 10A
₹65.00 (Price is Exclusive of GST)2 Channel 5V Relay Module
₹65.00 (Price is Exclusive of GST) -
Wire Cutter and Stripper
- Flawless Finish
- Optimum Strength
- Best Quality
- Cutting range of wire 0.5mm to 2.5mm & 6mm
- Also Suitable for Electronic, Aviation &Â Automobile sectors
₹65.00 (Price is Exclusive of GST)Wire Cutter and Stripper
₹65.00 (Price is Exclusive of GST) -
Wire Clipper Nipper
Suitable for dressing components on printed circuit boards. Handles made out of ABS plastics. Diagonal cutters have intersecting jaws that cut the wire at an angle, leaving a flat tip.
₹65.00 (Price is Exclusive of GST)Wire Clipper Nipper
₹65.00 (Price is Exclusive of GST) -
KP08 8mm Bore Inner Ball Mounted Pillow Block Insert Bearing
Features :
- Durable with high precision
- Can withstand great weight
- The angle between the inner bearing and the outer fixing ring is adjustable
- Easy to install
₹62.90 (Price is Exclusive of GST)KP08 8mm Bore Inner Ball Mounted Pillow Block Insert Bearing
₹62.90 (Price is Exclusive of GST) -
₹62.00 (Price is Exclusive of GST)3-Cell 18650 Battery Holder Series-Parallel
₹62.00 (Price is Exclusive of GST) -
LM2596 DC Step Down Buck Converter Power Supply Module
- Input voltage: 4.5-40V,
- Output voltage: (3-35V) continuously adjustable (recommended load debugging).
- Minimum pressure: 1.5V
- Output current: rated current 2A, 3A maximum
- Output Power: 15W maximum
₹62.00 (Price is Exclusive of GST)LM2596 DC Step Down Buck Converter Power Supply Module
₹62.00 (Price is Exclusive of GST) -
Orange A Grade IFR14430 3.2V 400mAh 3C LiFePO4 Battery
- Shape:Â Cylindrical Battery
- Battery Type: LiFePO4 Battery
- High performance and capacity
- Flat top to suit many devices fitting
- Suitable for portable devices
₹61.00 (Price is Exclusive of GST)Orange A Grade IFR14430 3.2V 400mAh 3C LiFePO4 Battery
₹61.00 (Price is Exclusive of GST) -
M4 x 20mm CHHD Bolt and Nut Set-20Pcs.
M4 x 20mm
- Type: M4 (4.0mm Diameter)
- Material: Mild Steel
- Bolt Head Style: Slotted & Round
- Pack Quantity: 20 sets.
- Nut Type: Hex
₹61.00 (Price is Exclusive of GST)M4 x 20mm CHHD Bolt and Nut Set-20Pcs.
₹61.00 (Price is Exclusive of GST)
