-
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (excl. GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (excl. GST) -
Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹750.00 (excl. GST)Capacitive Soil Sensor V2.0 Wholesale/B2B (Pack of 25)
₹750.00 (excl. GST) -
Waveshare 7inch Capacitive Touch Screen LCD (B)
Features:
- 800×480 High-Resolution Display
- Capacitive Touch Control
- HDMI Interface for Display, USB Interface for Touch Control
- Supports Raspberry Pi, comes with Raspbian driver (Works directly with Raspbian), and Ubuntu Image
- Supports Banan Pi, Banana Pro, comes with LUbuntu, Raspbian Image
- Supports BB Black, comes with Angstrom Image
- Not only SBC’s, but it can also work with any computer display with HDMI Interface, Touch interface will not work in that case.
- Backlight control, for lower power consumption.
₹4,200.00₹4,600.00(excl. GST)Waveshare 7inch Capacitive Touch Screen LCD (B)
₹4,200.00₹4,600.00(excl. GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(excl. GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(excl. GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (excl. GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (excl. GST)
-
GT2 Timing Belt 200mm Width-6mm Closed-Loop Rubber Belt
GT2 Timing Belt 200mm Width-6mm
1 x GT2 Timing Belt 200mm Width-6mm Closed-Loop Rubber Belt for 3D Printer
₹46.00 (excl. GST)GT2 Timing Belt 200mm Width-6mm Closed-Loop Rubber Belt
₹46.00 (excl. GST) -
GT2 Close-Loop Rubber Timing Belt for 3D Printer
GT2 Close-Loop Rubber Timing Belt
- Pitch: 2mm
- Material: Neoprene Rubber With Fiberglass Core
- Width: 6mm
- Total Length: 188mm
- Belt Height: 1.52 mm
- Tooth Height: 0.76mm
- Shape: Closed Loop
₹43.00 (excl. GST)GT2 Close-Loop Rubber Timing Belt for 3D Printer
₹43.00 (excl. GST) -
IR2110 High and Low Side Driver IC DIP-14 Package
IR2110 High and Low Side Driver
Features:-
- Floating channel designed for bootstrap operation Fully operational to +500V or +600V Tolerant to negative transient voltage dV/dt immune
- Gate drive supply range from 10 to 20V
- Undervoltage lockout for both channels
- 3.3V logic compatible Separate logic supply range from 3.3V to 20V Logic and power ground ±5V offset
- CMOS Schmitt-triggered inputs with pull-down
- Cycle by cycle edge-triggered shutdown logic
- Matched propagation delay for both channels
- Outputs in phase with inputs
₹108.00 (excl. GST)IR2110 High and Low Side Driver IC DIP-14 Package
₹108.00 (excl. GST) -
MC1458P Amplifier IC
MC1458P Amplifier IC
This general purpose amplifier MC1458P OP amp is a simple circuit component used for signal amplification. Its typical dual supply voltage is ±9|±12 V, with a minimum of ±5 V and maximum of ±15 V. This op amp has a temperature range of 0 °C to 70 °C. This device uses dual power supplies. It has 2 channels per chip. This device utilizes bipolar technology.
₹57.00 (excl. GST)MC1458P Amplifier IC
₹57.00 (excl. GST) -
OP07CP Amplifier ICs
OP07CP Amplifier ICs
- IC Name: OP07
- Package/Case: DIP-8
₹16.00 (excl. GST)OP07CP Amplifier ICs
₹16.00 (excl. GST) -
TL084 Quad JFET Input Operational Amplifier (Op-Amp) IC DIP
TL084 Quad Amplifier
Features:-
• Low Power Consumption: 1.4 mA/ch Typical
• Wide Common-Mode and Differential Voltage Ranges
• Low Input Bias Current: 30 pA Typical
• Low Input Offset Current: 5 pA Typical
• Output Short-Circuit Protection
• Low Total Harmonic Distortion: 0.003% Typical
• High Input Impedance: JFET Input Stage
• Latch-Up-Free Operation
• High Slew Rate: 13 V/μs Typical
• Common-Mode Input Voltage Range
• Includes VCC+
₹24.00 (excl. GST)TL084 Quad JFET Input Operational Amplifier (Op-Amp) IC DIP
₹24.00 (excl. GST) -
RC4558P Operational Amplifiers
RC4558P Operational Amplifier
Subcategory:Amplifier ICs
Supply Type:Single, Dual
Technology:Bipolar
Voltage Gain dB:109.54 dB
Width:6.35 mm
Unit Weight:440.400mg
₹23.00 (excl. GST)RC4558P Operational Amplifiers
₹23.00 (excl. GST) -
NE5532 Dual Noise High-Speed Audio Operational Amplifier IC DIP-8 Package
NE5532
Features:-
• Equivalent Input Noise Voltage:
• 5 nV/√Hz Typ at 1 kHz
• Unity-Gain Bandwidth: 10 MHz Typ
• Common-Mode Rejection Ratio: 100 dB Typ
• High DC Voltage Gain: 100 V/mV Typ
• Peak-to-Peak Output Voltage Swing 26 V Typ With VCC± = ±15 V and RL = 600 Ω
• High Slew Rate: 9 V/μs Typ
₹20.00 (excl. GST)NE5532 Dual Noise High-Speed Audio Operational Amplifier IC DIP-8 Package
₹20.00 (excl. GST) -
Q250 Quadcopter Super Strong Carbon Fiber 4mm Arm FPV Racing Frame(250mm) Kit
Q250 Quadcopter
Features :
- Lightweight and Durable.
- Made by super strong and advanced engineering material.
- The frame has excellent strength.
- The arm equips dampers for the safe landing.
- The arm has multiple motor mounting holes.
- Equips vibration-free mounting bracket for FPV camera.
₹975.00 (excl. GST)Q250 Quadcopter Super Strong Carbon Fiber 4mm Arm FPV Racing Frame(250mm) Kit
₹975.00 (excl. GST) -
OTG Android 5.8G UVC AV Phone Receiver
OTG Android
- Model: ROTG01
- Name: UVC OTG FPV Receiver
- Channel: 150CH
- Power Supply: 5V(by smartphone)
- Connector: SMA Female
₹2,061.00 (excl. GST)OTG Android 5.8G UVC AV Phone Receiver
₹2,061.00 (excl. GST) -
TS835 FPV 5.8G Wireless AV Transmitter – 600Mw 48Ch (2-6S)
TS835 FPV 5.8G Wireless AV Transmitter
1 x 48 CH AVTransmitter.1 x Power cable1 x A Removable Antenna₹1,450.00 (excl. GST)TS835 FPV 5.8G Wireless AV Transmitter – 600Mw 48Ch (2-6S)
₹1,450.00 (excl. GST) -
Weighing Load Cell Sensor 1Kg for Electronic Kitchen Scale YZC-131 With Wires
Load Cell Sensor 1Kg
- Weighing Range: 0 ~ 1 kg.
- Rated Output: 1.0 ± 0.1mV / V.
- Non Linear Output: ± 0.03% F.S.
- Input Impedance: 1066 ± 10% Ω.
- Output Impedance: 1000 ± 10% Ω.
- Insulation Resistance: 2000 MΩ.
₹116.00 (excl. GST)Weighing Load Cell Sensor 1Kg for Electronic Kitchen Scale YZC-131 With Wires
₹116.00 (excl. GST)
