No products in the cart.
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹690.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹690.00(Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹215.00 (Price is Exclusive of GST)
Pro-Range INR 21700 P42A 14.8V 12600mAh 4S3P 110A/140A Discharge Li-ion Drone Battery Pack
- Nominal Capacity (mAh): 12600
- Nominal Voltage (v): 14.8
- Max Charging Voltage (v): 16.8
- Charge Port: 5 Pin JST XH
- Discharge Port: Amass XT90 AS
₹7,214.00 (Price is Exclusive of GST)Pro-Range INR 21700 P42A 14.8V 12600mAh 4S3P 110A/140A Discharge Li-ion Drone Battery Pack
₹7,214.00 (Price is Exclusive of GST)ATL Package 4 (DIY Tinkering and Safety Equipments)
The Atal Tinkering Lab (ATL) initiative is aimed at enhancing the Indian Education System. It is converting thoughts to reality, where the young children (max 12 years of age) are being introduced to the world of technological innovation. ATL made to experience totally different microenvironments in Indian schools. This is allowing the children to work around their area of interest without having a fixed syllabus.
₹7,700.00₹8,500.00(Price is Exclusive of GST)ATL Package 4 (DIY Tinkering and Safety Equipments)
₹7,700.00₹8,500.00(Price is Exclusive of GST)
G1200 1200 x 12MP Multipurpose Digital Electronic Microscope with 7″ LCD Display
Save & output of Images and Videos: This LCD Screen digital microscope is equipped with a Micro SD card slot and 32G of the card. You can save the images and videos obtained during your observations to the 32G tf card and output.(Maximum support for 64G Micro SD cards)
Great Gift : This LCD digital microscope is perfect for circuit board inspection, QC inspection, watch/clock repair, textile industrial, kids education inspection, biological observation (not suitable for cells), medical professionals, scientific researchers, insects, coins, jewelry, and stamps. It’s the best gift for children, students, hobbyists, and other users.
₹9,500.00 (Price is Exclusive of GST)G1200 1200 x 12MP Multipurpose Digital Electronic Microscope with 7″ LCD Display
₹9,500.00 (Price is Exclusive of GST)Pro-Range INR 21700 P42A 14.8V 16800mAh 4S4P 150A/185A Discharge Li-ion Drone Battery Pack
- Nominal Capacity (mAh): 16800
- Nominal Voltage (v): 14.8
- Max Charging Voltage (v): 16.8
- Charge Port: 5 Pin JST XH
- Discharge Port: Amass XT90 AS
₹9,659.00 (Price is Exclusive of GST)Pro-Range INR 21700 P42A 14.8V 16800mAh 4S4P 150A/185A Discharge Li-ion Drone Battery Pack
₹9,659.00 (Price is Exclusive of GST)Cretile Voyager Kit – (37 Cretiles and Accessories)
Set of 37 Cretile circuit modules:
- Battery/Power Supply – 1
- Battery/Power Supply – 2
- Geared Motor – 1
- Geared Motor – 2
- High Speed Motor
- Obstacle Sensor – 1
- Obstacle Sensor – 2
- Switch
- Buzzer
- Inverter – NOT Gate
- Dimmer
- Light Sensor
- Light
- Copy
- Submersible Water Pump
- Sensor Base – 1
- Sensor Base – 2
- Transmitter
- Receiver
- Pulse/Delay (Timing functionality)
- Pump/Motor
- Push Button – 1
- Push Button – 2
- Sound Sensor
- Motion Sensor
- Connectivity Sensor
- Limit Switch (approach sensor)
- Wire
- U-Right
- Robotic Wheel – 1
- Robotic Wheel – 2
- Pipe for pump
- Small Wheel
- USB Rechargeable 9V Battery
- Non-rechargeable 9V battery
- Pulley
- Fan Blade
These Cretile blocks can be used to create various projects. Your creativity will define what you can create out of it.
₹9,838.00 (Price is Exclusive of GST)Cretile Voyager Kit – (37 Cretiles and Accessories)
₹9,838.00 (Price is Exclusive of GST)Basic Robotics kit
Basic Robotics kit
Breadboard – 1
DC Motor – 1
Buzzer – 1
Green LED – 1
Red LEDs – 2
Push Button Switches – 3
Slide Switch – 1
Red Alligator Clip – 1
Black Alligator Clip – 1
Connecting Towers – 6
10kΩ Resistor – 1
20kΩ Resistor – 1
3.3kΩ Resistor – 1
Capacitor – 1
Jumper Wires – 3
₹10,170.00 (Price is Exclusive of GST)Basic Robotics kit
₹10,170.00 (Price is Exclusive of GST)Quadcopter Drone DIY Kit – V1
- Built from quality glass fiber and polyamide nylon.
- Integrated PCB connections for direct soldering of your ESCs
- Pre-threaded brass sleeves for all of the frame bolts.
- Colored arms for orientation to keep you flying in the right direction.
- Large mounting tabs on main frame bottom plate for easy camera mounting.
- Easy assembly.
₹10,500.00 (Price is Exclusive of GST)Quadcopter Drone DIY Kit – V1
₹10,500.00 (Price is Exclusive of GST)Pro-Range INR 21700 P42A 22.2V 12600mAh 6S3P 110A/140A Discharge Li-ion Drone Battery Pack
- Nominal Capacity (mAh): 12600
- Nominal Voltage (v): 22.2
- Max Charging Voltage (v): 25.2
- Charge Port: 7 Pin JST XH
- Discharge Port: Amass XT90 AS
₹10,845.00 (Price is Exclusive of GST)Pro-Range INR 21700 P42A 22.2V 12600mAh 6S3P 110A/140A Discharge Li-ion Drone Battery Pack
₹10,845.00 (Price is Exclusive of GST)Robotics & AI Kit
Robotics & AI Kit
- Expansion Board – 1
- Microcontroller Board/ Microprocessor Board – 1
- Ultrasonic Sensor – 2
- Potentiometer Module – 4
- Light Sensor – 4
- Servo Motor – 6
- Magnetic Sensor – 1
- LED Module – 4
- Flame Sensor – 1
- Push To Lock Switch Module – 4
- IR Sensor – 1
- DC Motor – 4
- Microcontroller Board/ Microprocessor Board – 1
- Soil Moisture Sensor – 1
- Push Button Switch Module – 4
- Seven Segment Display – 1
- Temperature Sensor – 1
- Buzzer Module – 1
₹11,823.00 (Price is Exclusive of GST)Robotics & AI Kit
₹11,823.00 (Price is Exclusive of GST)Pro-Range INR 21700 P42A 14.8V 21000mAh 4S5P 190A/230A Discharge Li-ion Drone Battery Pack
- Nominal Capacity (mAh): 21000
- Nominal Voltage (v): 14.8
- Max Charging Voltage (v): 16.8
- Charge Port: 5 Pin JST XH
- Discharge Port: Amass XT90 AS
₹11,989.00 (Price is Exclusive of GST)Pro-Range INR 21700 P42A 14.8V 21000mAh 4S5P 190A/230A Discharge Li-ion Drone Battery Pack
₹11,989.00 (Price is Exclusive of GST)Anycubic Kobra Neo-3D Printer
Technical Specifications
● Leveling: 25-point automatic leveling
● Printing platform: 8.7 x 8.7 inches / 220 x 220 mm
● Filament run-out detection: optional
● Printing material: PLA / ABS / PETG & TPU
● Nozzle size: ø 0.4 mm (replaceable)
● Nozzle temperature: ≤ 500 °F / 260 °C
● Hot bed temperature: ≤ 230 °F / 110 °C
● Printing speed: ≤100 mm/s (Max speed)
● Control panel: 2.4″ LCD screen with a control knob
● Z-axis: single threaded rod
● Printing dimensions: 250 x 220 x 220 mm (HWD)
● Machine dimensions: 490 x 445 x 443 mm
₹12,100.00 (Price is Exclusive of GST)Anycubic Kobra Neo-3D Printer
₹12,100.00 (Price is Exclusive of GST)Ender 3 FDM 3D Printer
Features
- Easy and Quick Assembly: It comes with several assembled parts, you only need about 2 hours to assemble 20 nuts well.
- Advanced Extruder Technology: Upgraded extruder greatly reduces plugging risk and bad extrusion; V-Shape with POM wheels makes it move noiseless, smoothly, and durable.
- Safety Protected Power Supply: Only needs 5 minutes for the hotbed to reach 110℃.
- It is a great project for middle school and high school-aged students. The perfect gift to spark a lifelong love for science and engineering, and provide a deeper understanding of machinery and robotics.
Max Print Speed : 80mm/s Auto Levelling : NA Print Bed Removeable : NA Supported files : STL，OBJ，G-Code Camera : NA Connectivity : USB or SD offline
₹12,122.00 (Price is Exclusive of GST)Ender 3 FDM 3D Printer
₹12,122.00 (Price is Exclusive of GST)
