-
NE555 Frequency Adjustable Pulse Generator Module
- Single channel signal output, the output duty cycle about 50% square wave.
- Plate load resistor, adjust the resistance to control the output frequency.
- Onboard power indicator.
- Working voltage: 5V~12V.
- Onboard NE555 IC.
₹35.00 (Price is Exclusive of GST)NE555 Frequency Adjustable Pulse Generator Module
₹35.00 (Price is Exclusive of GST) -
UNO R3 with USB Cable Compatible with Arduino
- Micro-controller : ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
₹540.00₹638.00(Price is Exclusive of GST)UNO R3 with USB Cable Compatible with Arduino
₹540.00₹638.00(Price is Exclusive of GST) -
LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
- Operating Voltage (VDC) 3.3
- Digital I/O Pins 26
- Analog I/O Pins 12
- Clock Speed 240 MHz
- Flash Memory 4 MB
₹405.00 (Price is Exclusive of GST)LOLIN32 V1.0.0 based on ESP32 Rev1 Wifi Bluetooth Board
₹405.00 (Price is Exclusive of GST) -
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 (Price is Exclusive of GST)4 Channel 5V Relay Module with Optocoupler
₹160.00 (Price is Exclusive of GST) -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹264.00 (Price is Exclusive of GST)Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
₹264.00 (Price is Exclusive of GST) -
Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
Wiring Connection
VCC: 3.3V-5V
GND: GND
DO: Digital output interface(0 and 1)
AO: Analog output interfaceFeatures :
- Dual output mode, analog output more accurate
- A fixed bolt hole for easy installation
- With power indicator (red) and digital switching output indicator (green)
- Having LM393 comparator chip, stable.
₹690.00 (Price is Exclusive of GST)Soil Moisture Sensor Module Wholesale/B2B (Pack of 25)
₹690.00 (Price is Exclusive of GST) -
Capacitive Soil Sensor V2.0
- Operating Voltage: 3.3 ~ 5.5 VDC.
- Operating Current: 5mA.
- Interface: PH2.54-3P.
- Supports 3-Pin Gravity Sensor interface
- Intelligent agriculture
₹60.00 (Price is Exclusive of GST)Capacitive Soil Sensor V2.0
₹60.00 (Price is Exclusive of GST) -
ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
- This DHT11 temperature and humidity sensor shield is specially designed for ESP8266 ESP-01 ESP-01S development board.
- On-board 8pin socket enable you plug the wifi transceiver to the board directly perfect for DIY your wireless temperature/humidity webserver system.
- Working Voltage: DC 3.7 – 12V
- The weight of about 10 grams
- Package Included: 1 X DHT11 Humidity Temperature Sensor
₹130.00 (Price is Exclusive of GST)ESP8266 ESP-01/ESP-01S – DHT11 Temperature Humidity Sensor Module
₹130.00 (Price is Exclusive of GST) -
Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
- Automatic relay controller board for sanitiser machine
- No extra connections required
- Just connect Ir sensor, water pump and power supply
- Easy to use DIY kit
₹207.00 (Price is Exclusive of GST)Automatic Sanitizer Dispenser Tunnel Control Board with inbuilt Sensor Interface Port for Ultrasonic and IR, Relay, Timer Control and Motor Kit
₹207.00 (Price is Exclusive of GST) -
Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
- Robotics Kit Arduino based Do it Yourself Type Kit
- Explorer Board- UNO compatible microcontroller board with integrated motor controllers, RGB LED, and breadboard
- Power Supply Module- To be used with 18650 Li-Ion batteries with on-board charge and usage switches
- Acrylic Chassis- Consists of two layers for mounting the electronics and serves as the chassis of the robot. Also contains 4 nylon spacers for connecting the top and bottom layers.
- Micro Metal gear motors- Two motors used for robot mobility. Wheels & Tyres- Plastic wheels with silicone tyres for great traction.
- Line Following Array- Line following sensor consisting of 5 individual sensors to help in projects such as line following. Ultrasonic Sensor- Adds distance sensing capability to your project.
₹3,450.00₹4,500.00(Price is Exclusive of GST)Explorer Kit for Robotics and DIY Prototyping Compatible with Arduino IDE
₹3,450.00₹4,500.00(Price is Exclusive of GST)
-
1S 2A BMS Board 3.7V 18650 Lithium Battery Protection Board
Features:
- Easy to use
- Color: Green
- The internal resistance difference is not more than 5mQ
- BMS Li-ion Battery Protection Board
- The tolerance is less than 30mAh
- Single-cell consumption of battery (self-consumption): ≤3uA
- In this MOSFET are employed to do the monitoring task which protects our battery cells from overcharge
Precautions:1. Before installing the protection board, the battery should be matched well (the voltage difference between each battery should not be 0.05V, the internal resistance difference is not more than 5mQ, the tolerance is less than 30mAh), the smaller the battery voltage difference, the better the protection board will work. .2. The batteries are connected in parallel and then connected in series, and the welding is correct (18650 battery nickel spot welding, other batteries are soldered), do not screw, easy to burn the protection board IC.3. If it is an old battery change board, please pay attention: Please confirm the battery is normal before buying?4. When installing, use a multimeter to check whether the voltage of each string is the same. The performance failures with a difference of more than 1.0V are: running not far, starting and powering off, charging time is short, basically the battery core problem is more. The failure of the protection board is as follows: the battery cannot be charged, and the battery has a voltage and cannot be discharged.₹15.00 (Price is Exclusive of GST)1S 2A BMS Board 3.7V 18650 Lithium Battery Protection Board
₹15.00 (Price is Exclusive of GST) -
₹15.00 (Price is Exclusive of GST)6K8 Wire Wound Resistor 10W ±5%
₹15.00 (Price is Exclusive of GST) -
170 Points Mini Bread Board
- 170 Tie-points for Arduino Raspberry Pi
- Colour May Vary
- Great addition to your hobby craft tool kit
- Perfect product for your saftey and lab supply
- ABS Plastic material
₹15.00₹22.00(Price is Exclusive of GST)170 Points Mini Bread Board
₹15.00₹22.00(Price is Exclusive of GST) -
ULN2003 Stepper Motor Driver IC
- 500-mA-Rated Collector Current (Single Output)
- High-Voltage Outputs: 50 V
- Output Clamp Diodes
- Inputs Compatible With Various Types of Logic
- Relay-Driver Applications
₹15.00 (Price is Exclusive of GST)ULN2003 Stepper Motor Driver IC
₹15.00 (Price is Exclusive of GST) -
Tactile Push Button Switch 6x6x5 (Pack of 10)
- Ideal for Through-hole applications.
- Shaft Shape: Round
- Used in the fields of electronic products, household appliances and more.
-
This light touch switch is waterproof, prevent oil, anti-pollution, anti-static interference.
-
High precision mechanism design offers acute operation and long service life.
-
Compact and lightweight, easy to carry and dismantling.
-
Good electrical conductivity.
₹14.50 (Price is Exclusive of GST)Tactile Push Button Switch 6x6x5 (Pack of 10)
₹14.50 (Price is Exclusive of GST) -
FRC connector male 40 pin (Pack of 2)
-
Features/Specs:
- 40 Pin Box Header Male Straight
- Arrangement: 20 x 2 pins
- Pitch: 2.54 mm
- Current Rating: 3 A max
- Working Voltage: 250V AC
- Gender: Male
- Connector Type: IDC
- Current Rating: 3A
- Insulation Resistance: 1000MΩ MIN
- Contact Impedance: 15mΩ MAX
- Mounting Type: PCB Mount
- Contact Material: Phosphor Bronze
- Operating Temperature: -25°C ~ +105°C
- Housing Material: Thermoplastic
- Contact Plating: Nickel-plated terminals
- Color: Black
₹14.00 (Price is Exclusive of GST)FRC connector male 40 pin (Pack of 2)
₹14.00 (Price is Exclusive of GST) -
-
Male DC Power Plug Jack Connector
- Excellent material, fine workmanship.
- Suitable for 6 to 30 V 1A Applications
- Compatible with 5.5mm barrel female jacks
- Color: Black.
- Avoid the polarity conflict and short circuit.
₹14.00 (Price is Exclusive of GST)Male DC Power Plug Jack Connector
₹14.00 (Price is Exclusive of GST) -
Set of 1 ALLEN KEY and 10 GRUB Screw M3*4 Set for Timing Pulley of 3D Printers
- Material: Steel
- Set: M3x4
- Length of Allen Key: 48 mm
- Width of Allen Key: 1.5 mm
- Inner Diameter of grub: 1.5 mm
- Outer Diameter of Grub: 2.8 mm
₹13.00 (Price is Exclusive of GST)Set of 1 ALLEN KEY and 10 GRUB Screw M3*4 Set for Timing Pulley of 3D Printers
₹13.00 (Price is Exclusive of GST) -
Set of 1 ALLEN KEY and 10 GRUB Screw M4*5 Set for Timing Pulley of 3D Printers
- Material: Steel
- Length of Allen Key: 48 mm
- Width of Allen Key: 1.9 mm
- Inner Diameter of grub: 2 mm
- Outer Diameter of Grub: 3.8 mm
₹13.00 (Price is Exclusive of GST)Set of 1 ALLEN KEY and 10 GRUB Screw M4*5 Set for Timing Pulley of 3D Printers
₹13.00 (Price is Exclusive of GST) -
Voltage Detection Sensor Module 25V
Features :
- Output Interface: “+ ” connected 5/3.3V, “-” connected GND, “s” connected Arduino AD pins
- DC input interface: red terminal positive with VCC, negative with GND
- You can also use the IICLCD1602 LCD to display voltage.
- By 3P connector, connect this module with the expansion of board Arduino, not only makes it easier for you to detect voltage battery.
₹13.00 (Price is Exclusive of GST)Voltage Detection Sensor Module 25V
₹13.00 (Price is Exclusive of GST) -
100nF 1206 Surface Mount Multilayer Ceramic Capacitor(Pack of 3)
Features:
- Supplied in tape on reel
- Nickel-barrier end termination
- RoHS compliant
- Halogen-free compliant
₹13.00 (Price is Exclusive of GST)100nF 1206 Surface Mount Multilayer Ceramic Capacitor(Pack of 3)
₹13.00 (Price is Exclusive of GST) -
TTP223B Digital Capacitive Touch Sensor Module
- Low power consumption.
- Power supply for 2 ~ 5.5V DC
- Can replace the traditional touch of a button, touch area.
- Four m2 screws positioning holes for easy installation, power indicator green led, power on the right that is shiny.
- Control interface : A total of three pins (gnd, vcc, sig), gnd to ground , vcc is the power supply , sig digital signal output pin.
₹13.00₹35.00(Price is Exclusive of GST)TTP223B Digital Capacitive Touch Sensor Module
₹13.00₹35.00(Price is Exclusive of GST)
