-
4 Channel 5V Relay Module with Optocoupler
- No. of Channel: 4
- Trigger Voltage: 5VDC
- Triode drive, increasing relay coil
- High impedance controller pin
- Pull-down circuit for the avoidance of malfunction
- Power supply indicator and Control indicator lamp
- Power supply and relay instructions, lit, the disconnect is off;
- The input signal, signal, common Terminal and start conducting;
₹160.00 -
5V 16 Channel Relay Module with Light Coupling LM2596S Power Supply
Features :
- 5V 16-Channel Relay Module with AC contact capacity of 10A 250V and optocoupler protection.
- Onboard power supply module does not need an external power supply. I / O port driver is active low.
- The module can be used as a microcontroller development board module and also as appliance control, PLC extended output.
- It is using the industry’s top -quality isolation optocouplers, strong anti-jamming ability, stable performance.
- The 1-16 road can be any full on/off or any road.
- Each relay common terminal “COM” are independent, user-friendly access to different signals, each relay are normally closed and normally open with the port.
- Each relay is equipped with motion lights.
- All interfaces can be directly connected through the terminal leads, very convenient.
₹546.00 -
5V 8 Channel Relay Module
Features:
- The 8550 transistor drive, drive ability.
- A fixed bolt holes for easy installation.
- It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red)
- Relay control interface by single-chip IO.
- Low-level suction close, high-level release.
- Easy to use, simple 3 line structure.
₹285.005V 8 Channel Relay Module
₹285.00 -
5V WiFi Relay Module v1.0 for ESP8266 ESP01S- IOT Smart Home Remote Control Switch
- Operating Voltage: DC 5V
- Transmission range: the maximum transmission range of 400m (open environment, mobile phone equipped with WIFI module)
- Load capacity: 10A / 250VAC 10A / 30VDC, the relay pulls 100,000 times
- Designed for smart home, internet of thing and other DIY project.
₹225.00 -
Buzzer Module Board-3.3 to 5V
- Operating voltage: 3.3V-5V
- PCB Dimension: 3.1cm*1.3cm.
- Color: Blue
- Easy to use
₹30.00 -
DS1302 Real Time Clock Module (RTC)
Features:-
- Real-Time Clock Counts Seconds, Minutes, Hours, Date of the Month, Month, Day of the Week, and Year with Leap-Year Compensation Valid Up to 2100
- Serial I/O for Minimum Pin Count
- 2.0V to 5.5V Full Operation
- Uses Less than 300nA at 2.0V
- Single-Byte or Multiple-Byte (Burst Mode) Data Transfer for Read or Write of Clock or RAM Data
₹95.00 -
Dual Channel Digital Power Board XH-M543, DC12-26V 2x120W DIY Module High Power Stereo Amp Board for Car Vehicle Computer Speaker DIY Home Theater Audio System
- Strong TPA3116D2 chip is a digital power amplifier chip, with low idle loss characteristics,makes it work well and quickly.
- On board front-facing IC to improve the input sensitivity, high-definition sound quality
- This product has the characteristics of loud sound ,the capacitance are large, ,excellent sound quality.
- There is no solder joint on the back of the circuit board,the chip capacitors and the solder solder board together, so there is no possibility of short circuit.
₹665.00 -
Dual Channel TDA7297 Amplifier Board AC/DC 12V Module
- TDA7297 power amplifier board, connecting terminals all adopt XH2.54 needle seat, quick installation
- 2.0 dual channel 15W+15W output, can be connected to 4-8 Euro 10-50W speakers, wide range of applications
- Voltage: DC 9-15V, recommended DC voltage 12V, current 2A or more
- Power: 15W+15W
- Impedance: 4-8 ohms
₹215.00 -
Dual-axis XY Joystick Module
- Input voltage range: DC 3.3V to 5V, Quality rocker, long life, stable performance
- Two analog outputs, one digital output
- X, y-axis output of the two potentiometers can be read out through the a to d converter
- Cross joystick is a bi-directional 10K resistor, with the rocker in different directions, the tap resistance with the change. This module uses 5V power supply, the original state of X, Y read voltage of 2.5V or so, when pressed with the arrow direction, the read voltage value increases with the maximum to 5V; arrows in the opposite direction to press, read the voltage decreases , The minimum is 0V.
- Package content: 1 joystick module
₹42.00Dual-axis XY Joystick Module
₹42.00 -
Laser sensor Module 650nm 6mm 5V 5mW Red Laser
- Voltage: 3.0 V – 5 V.
- Driver: APC circuit.
- Line length: about 135 mm.
- Transmit power: 58mW.
- Operating Current: 40mA.
- Operating Current: 40mA.
- Operating temperature: -36◦C ~ 65◦C.
₹39.00 -
LED Traffic Lights Signal Module / Digital Signal Output Traffic Light Module
- PCB Size: 60 x 20 x 13.5 (LxWxH)mm.
- Color: red, yellow, green
- LED Size: 10mm x 7.
- Brightness: Normal brightness.
- Voltage: 5V.
- Interface: common cathode red yellow green control.
₹38.00
All Categories
- Atal Tinkering Lab (ATL)
- 3D Printer & Accessories
- Communications & Interfacing
- Connector & Cable Wires
- Consumer Products
- Development Boards
- Educational DIY & STEM Kits
- Electronic Components
- Electronic Modules & Displays
- Power Supply & Prototypes
- Robotics & Hobbies
- Sensors
- Tools & Equipments
- Bulk/Wholesale
